We think you have liked this presentation. If you wish to download it, please recommend it to your friends in any social system. Share buttons are a little bit lower. Thank you!
Presentation is loading. Please wait.
Published byAlia Goold
Modified about 1 year ago
Reading Technical Drawings: Test Foundations of Manufacturing
1. What is the part number? 11A001 Thermostat Gasket
2. What is the name of the part? Thermostat gasket Thermostat Gasket
3. What is the drawing size? (A, B, or C) A Thermostat Gasket
4. What scale is the drawing? 1:1 Thermostat Gasket
5. Use words to explain the answer to question 4. Actual size Thermostat Gasket
6. How thick is the part?.06 Thermostat Gasket
7. Is the part symmetrical? Yes Thermostat Gasket
8. Which system of dimensioning was used? (Refer to page 21.) Decimal Thermostat Gasket
9. What is the fractional equivalent of the center hole size? 2 3/16 Thermostat Gasket
10.What is the fractional equivalent of the mounting hole spacing? (Refer to the equivalency chart, page 25.) 3 5/8 Thermostat Gasket
11. Calculate the longest overall dimension of the part. 4.24 Thermostat Gasket
12. Calculate the overall dimension of the part (height.) 2.88 Thermostat Gasket
13. Calculate the material remaining between the large hole and the nearest outside edge..345 Thermostat Gasket
14. Calculate the material remaining between the small hole and the nearest outside edge..155 Thermostat Gasket
15. Calculate the material remaining between the large hole and the nearest small hole..56 Thermostat Gasket
Reading Technical Drawings: Test Foundations of Manufacturing
Reading Technical Drawings Foundations of Manufacturing.
Fractions and Decimal Fractions Fractions Decimal Fractions
People Fractions. Problem 1 of 20 Answer 1 = 10 Problem 2 of 20 Answer 2 = 5.
WALT- use a number line to help round numbers to the nearest whole number to the nearest whole number to the nearest whole number.
LESSON #13 A REVIEW OF ORTHOGRAPHIC PROJECTION What is drafting? As explained in a previous lesson: Drafting is a Graphic Language that uses Lines, Symbols.
Which answer includes a mixed number that is equivalent to one and three twelfths.
Equivalents ½ ½ ⅔.
I can use proportions to solve problems involving scale.
Lesson 4: Equivalent Fractions Date: Objective: SWBAT find equivalent fractions and compare fractions Do Now: DON”T DO THE OPENING. NEED TO ADJUST.
Part 1-Section 1 Lines Unit 4 Extension Lines And Dimension Lines.
Catalyst Thursday, October 6, 2011 Of the 75 teachers at a school, 15 teach mathematics. What percent of the teachers at the school teach mathematics?
Structural Drafting Connection Details and Gages.
Scale Drawing - a two dimensional drawing that is similar to the object it represents. Scale Model - a three-dimensional model that is similar to the object.
Functional Maths Skills Online Activities Northern College
Introduction to Dimensioning © 2012 Project Lead The Way, Inc.Introduction to Engineering Design.
Competency: Design and draw interior elevations for kitchens and baths Objective: Develop plans for kitchen cabinets.
6.14 SOL 6.14 The student, given a problem situation, will a) construct circle graphs; b) draw conclusions and make predictions, using circle graphs; and.
Multiplication of Decimal Fractions STEPS : 1. Count the number of places BEHIND the decimals 2. Treat the problem like you are multiplying whole numbers.
By: Sean F.. Solving Equations Finding VolumePercent Increase and Decrease Measure of angles and shapes Multiplying Fractions and Decimals
© Nuffield Foundation 2012 Free-Standing Mathematics Activity Fractions, decimals, percentages.
Equivalent lists. The Ratio p : q is What is the scaling from p to q as as a fraction? as a decimal ? Increase or Decrease ? INVERSE The Ratio q : p is.
Working with Percentages. Writing percentages as fractions ‘Percent’ means ‘out of 100’. To write a percentage as a fraction we write it over a hundred.
5 Minute Math In which place is the 4 in each of the following: 140,399 48, ,394 Write 2 equivalent fractions for each of the following:
We note that: Math Trick: Multiplications of Numbers 25 35 = ? 25 = =
Decimals and Fractions. Decimals tenthshundredthstenths hundredths thousandths
Converting Fractions to Decimals Ms. Stewart Math 7 COPY SLIDES WITH A PENCIL ICON.
FIND THE UNIT RATE 9000 tickets 6 hours. FIND THE UNIT RATE 240 tickets = x tickets hour minute.
Converting Fractions to Decimals Adapted from free Powerpoints from the website:
Chapter 1 Section 3 Measurement. Objectives and Questions.
Converting Decimals to Percents Converting Fractions to Decimals Converting Percents to Decimals Converting Decimals to Fractions Converting from Fraction.
T9 Automoblox Detail Drawings Suggested Layouts Dimensioning Guidelines.
1 SheetCourse: Engineering Graphics 1504Memorial University of Newfoundland Engineering Graphics 1504 Lecture 2 – Orthographic Sketches Objectives l Recap.
Career & Technical Education Basic Drafting Skills Demonstrate correct drawing procedures.
Measuring and Drawing Angles with a Protractor. Protractor Center Hole.
On each number line, the distance from 0 to 1 represents one mile. These students each marked the distance they live from school on the number lines below.
Pre-Algebra 7-9 Scaling Three-Dimensional Figures Pre-Algebra Homework Page 378 #10-18 & #32-39 (SR) Answers.
B L O O M S Evaluation Knowledge Evaluation Analysis Application Comprehension Analysis PLENARYPLENARY.
Core Focus on Decimals & Fractions Measuring in Centimeters Lesson 1.3.
8’ - 4” 1’ - 8”. Unit 8 Dimensioning Scale dimensions from a print Read dimensions on a print Identify the items that should be dimensioned on different.
1 Blueprint Reading for the Machine Trades, Sixth Edition Unit 12: Auxiliary Views Russ Schultz and Larry Smith PowerPoint presentation created by LaVonne.
The Fractions Challenge When you see a fraction, change it into the equivalent decimal number. When you see a decimal number, change it into the equivalent.
Measuring Note Cards Purpose: To measure the dimensions of an object as accurately and precisely as possible and to apply rules for rounding answers calculated.
Fractional/decimal equivalents There are several uses for equivalents for fractions in our shop. We need to know that ½ is.500 To use taps and dies To.
1 Technical Communications. 2 Objectives Understanding graphics as a communication tool Technical sketching Projections –Orthographic –Pictorial Sketching.
HOW BALANCED IS YOUR WHEEL?. To Figure out how balanced your wheel is… Take your totals from each category on your wellness wheel and put them on the.
IOT POLY ENGINEERING 2-15 January 25, 2010 Pass in your Line Weight Practice Get out the following: –Timeline project handout –Orthographic Projection.
Multiview Drawings. Multiview Drawing A multiview drawing is one that shows two or more two-dimensional views of a three- dimensional object. Multiview.
Study Lesson 4 Orthographic Writing. Suggestions on a view selection Contents Orthographic writing Primary auxiliary view Alignment of views (Projection.
Practice using fractions, decimals, and percents with place value, number lines, shaded shapes, and shaded 10 x 10 grids.
© 2017 SlidePlayer.com Inc. All rights reserved.