Presentation is loading. Please wait.

Presentation is loading. Please wait.

Digital Solutions Saving and Restoring the PLC.

Similar presentations


Presentation on theme: "Digital Solutions Saving and Restoring the PLC."— Presentation transcript:

1 Digital Solutions Saving and Restoring the PLC

2 Digital Solutions NC HN482card (SRAM/FROM) FROM area Area for COS1 Area for COS2 Temporary Storage Area ROM Write Copy When Power is on NC HN123card (Virtual: COS2 Side) NC HN163card (Real: COS1 side) Execute Ladder Onboard Edition area External Media PC side Project Save Project Open Save Open Edit/Monitor 1. Open ladder which is running in the NC on onboard edition area. 2. Save the opened ladder to the external media(USB, hard drive, etc) Page 42 Matrix Maint Manual Saving the PLC (LADDER) 1 2

3 Digital Solutions Press DIAGNOS soft key

4 Digital Solutions Press VERSION soft key

5 Digital Solutions Press LADDER MONITOR soft key Versions of Ladders COS1 COS2 Drawing

6 Digital Solutions Press ENVIRON SETTING soft key

7 Digital Solutions Press CONNECT NC SETTING soft key

8 Digital Solutions Select M01 on drop down menu and Press SET soft key Press far left F1 Display Menu Key once to get the first screen menu

9 Digital Solutions Press NC FILE soft key Step 1 (Open PLC)

10 Digital Solutions Press OPEN soft key

11 Digital Solutions Make sure that all files are selected--should be checked Press OPEN soft key

12 Digital Solutions Press OK soft key Press F1 Display Menu Key twice to get the first screen menu Drawing

13 Digital Solutions Press EXTERNAL FILE soft key Step 2 (Save Project to External Media)

14 Digital Solutions Press SAVE PROJECT soft key

15 Digital Solutions Make sure that all files are selected--should be checked Press EXTERNAL SAVE soft key

16 Digital Solutions Press DRIVE/PATH and select drive D for USB port D:\M01 Press PROJECT NAME and name ladder preferably with version

17 Digital Solutions Press SAVE soft key

18 Digital Solutions Press OK soft key once ladder is saved to external media

19 Digital Solutions Windows Explorer

20 Digital Solutions

21 Ladder Files

22 Digital Solutions  Repeat all of the previous steps  Select M02 for virtual ladder save

23 Digital Solutions Restoring the PLC (LADDER) STEPS: 1. Clear the ladder which runs in temporary storage area 2. Open the project saved in external media onto the onboard edition area 3. Load the opened ladder to the temporary storage area in the NC 4. Save the ladder into the ROM area(HN482 card) If steps 2 and 3 are performed without deleting the ladder in step 1 then there will be two different ladders registered Page 45 Matrix Maint Manual Must be in Privileged Mode to upload ladder

24 Digital Solutions NC HN482card (SRAM/FROM) FROM area Area for COS1 Area for COS2 ROM Write Copy When Power is on NC HN123card (Virtual: COS2 Side) NC HN163card (Real: COS1 side) Execute Ladder Onboard Edition area External Media PC side Project Save Project Open Save Open Edit/Monitor Temporary Storage Area 1 Erase Ladder 2 3 4

25 Digital Solutions Press DIAGNOS soft key

26 Digital Solutions Press VERSION soft key

27 Digital Solutions Press LADDER MONITOR soft key

28 Digital Solutions Press ENVIRON SETTING soft key

29 Digital Solutions Press CONNECT NC SETTING soft key

30 Digital Solutions Select M01 on drop down menu and Press SET soft key Press far left F1 Display Menu Key once to get the first screen menu

31 Digital Solutions Press NC FILE soft key Step 1 Drawing

32 Digital Solutions Press DELETE soft key

33 Digital Solutions Press SEL. ALL/CANCEL Soft key

34 Digital Solutions All files should be checked Press DELETE Soft key

35 Digital Solutions Press YES Soft key

36 Digital Solutions May see this screen, if so press YES Soft key to stop the ladder

37 Digital Solutions Press OK Soft key Press F1 Display Menu Key twice to get the first screen menu

38 Digital Solutions Notice Message Displayed Press EXTERNAL FILE Soft key Step 2 Drawing

39 Digital Solutions Press OPEN PROJECT Soft key

40 Digital Solutions Select d: drive and M01 folder

41 Digital Solutions Select Lad_Real file for project to upload

42 Digital Solutions Press SELECT Soft key

43 Digital Solutions Make sure all files are checked if not press SEL. ALL/CANCEL Soft key Press OPEN Soft key

44 Digital Solutions Press ALL YES Soft key May or May not get this message

45 Digital Solutions Press OK Soft key Press F1 Display Menu Key twice to get the first screen menu

46 Digital Solutions Step 3 Press NC FILE Soft key Drawing

47 Digital Solutions Press SAVE Soft key

48 Digital Solutions Make sure that all files are checked Press SAVE Soft key

49 Digital Solutions Press OK Soft key

50 Digital Solutions Step 4 Press ROM WRITE Soft key Drawing

51 Digital Solutions Press YES Soft key

52 Digital Solutions Press YES Soft key again to write ladder onto the ROM Very Important Step !

53 Digital Solutions Press OK Soft key Press far left F1 Display Menu Key once

54 Digital Solutions Press PLC RUN/STOP Soft key

55 Digital Solutions Press YES Soft key


Download ppt "Digital Solutions Saving and Restoring the PLC."

Similar presentations


Ads by Google