Presentation on theme: "Water Hydraulic Valves Introducing our range of For control of Main Inlet Valve Servo motor, service & maintenance seals Pressures up to 120 bar Flow."— Presentation transcript:
Water Hydraulic Valves Introducing our range of For control of Main Inlet Valve Servo motor, service & maintenance seals Pressures up to 120 bar Flow rates up to 600 litres/min 316L Stainless Steel Construction
Water Hydraulic Control Valves The 6mm Water Hydraulic Control valve is a ball seated type valve. The stainless steel / ceramic ball seat design ensures a virtual leak tight shut off. M.T.B.F., SFF, PFD and SIL Data (Available upon request) Easy Installation, Repair and Replacement Stainless Steel Construction Up to 120 bar Operating Pressure Range General Description The DN6 valve design incorporates a balanced internal piloting system and a lever mechanism to enable a wide range of operators to operate the valve. All valves have an ‘O’ Ring interface that enables them to be fitted with BSP.P ported subplates as standard, or manifold mounted to reduce pipework, fittings, weight and space. This interface also allows direct mounting of the valve to larger pilot operated valves up to the DN25, increasing the flow capacity to 200 l/min. By removing just 4 bolts the valves can be dismounted without disturbing pipework and possibly contaminating the hydraulic system. Blanking and flushing plates can also be supplied.
Water Hydraulic Control Valves Construction Materials Valve bodies and subplates: 316L Stainless Steel Wetted parts: Various grades of Stainless Steel/Super Duplex / Ceramic/Aluminium Bronze Seal Nitrile / Buna N / PTFE / Polyurethane Fasteners: A4, grade 80 stainless steel Springs: stainless steel Operating Temperature Range Standard: 5 ºC to + 60 ºC Ingress Protection (solenoids valves ) IP54 Operating Pressure Range 15 to 120 bar Operating Medium Filtered Fresh Water Recommended Filtration DN6: 10 microns DN15: 25 microns DN25: 25 microns DN40: 200 microns
Water Hydraulic Control Valves Hydraulic Pilot Operated 2 port, 2 position 3 port, 2 position 15 to 120 bar pressure range Flow rates up to 20 l/min Stainless Steel construction Pilot media, Oil or Water Solenoid Operated with Hydraulic Override Pilot 2 port, 2 position 3 port, 2 position 120 bar max. pressure Flow rates up to 20 l/min Stainless Steel construction 24VDC, 110VDC, 220VDC Override signal, oil or water Plunger or Roller Cam Operated 2 port, 2 position 3 port, 2 position 15 to 120 bar pressure range Flow rates up to 20 l/min Stainless Steel construction
Water Hydraulic Control Valves DN40 - Hydraulic Pilot Operated 3 port, 2 position 5 port, 2 position Pressure range 15 to 120 bar Flow rate up to 600 l/min Stainless Steel construction Pilot media, Oil or Water Remote position sensors 1 ½ “ SAE 3000 psi Flanged connections or BSP.P threaded ports Block before bleed function Operating temperature range 5 ºC to + 60 ºC Solenoid Operated 3 port, 2 position Flow rates up to 20 l/min 15 to 120 bar working pressure Stainless Steel construction DN15 & DN25 Solenoid operated Oil or Water pilot operated 3 port, 2 position 4 port, 2 position Pressure range 15 to 120 bar Flow rates up to 200 l/min Stainless Steel construction Pilot media, Oil or Water Easily replaceable one piece cartridge valve design
Water Hydraulic Control Valves Keep it simple ! Water Hydraulic Control Valves can simplify hydraulic control circuits and therefore increase reliability, while reducing maintenance and capital costs. Water Hydraulic Control Valves can replace conventional oil hydraulic power units and oil servo valves by utilizing the valuable natural renewable energy resource of water.