Presentation is loading. Please wait.

Presentation is loading. Please wait.

Copyright, 2006: Invisible Service Technicians, LLC Invisible Service Technicians, LLC Invisible Service Technician Monitor Activation Process: IST MaintSelectionV3.php.

Similar presentations


Presentation on theme: "Copyright, 2006: Invisible Service Technicians, LLC Invisible Service Technicians, LLC Invisible Service Technician Monitor Activation Process: IST MaintSelectionV3.php."— Presentation transcript:

1 Copyright, 2006: Invisible Service Technicians, LLC Invisible Service Technicians, LLC Invisible Service Technician Monitor Activation Process: IST MaintSelectionV3.php. Setup August 2006

2 Copyright, 2006: Invisible Service Technicians, LLC Monitor Configuration 1) Sales Order Procedure- see DN1040 2) Product Shipped 5) Data Center Updated 8) Create Customer (Profile Management) 3) IST Installed 4) IST Calls Collection Server 10) Enter “Monitored Equipment” (Data Center) 7) Enter “Installation information” (Data Center) 6) Contractor sends Info.- see DN1008, 1009 & ) Create Contractor (Profile Management) 12) Complete “Sensor Mapping” (Data Center) 13) Enter “Viewing Privileges” (Data Center) 11) Complete “Sensor Edit” (Data Center) 14) Enter “Alert Recipients” (Data Center) 15) Edit General Tab (IST Maint.) 17) Edit Thermo. Sensors Tab (IST Maint.) 16) Edit Temp Sensors Tab (IST Maint.) 19) Edit Calculations Tab (IST Maint.) 18) Edit Digital Sensors Tab (IST Maint.) 20) Edit Accumulator Tab (IST Maint.) 21) Edit Cycles Tab (IST Maint.) 22) Edit Alarms Tab (IST Maint.)

3 Copyright, 2006: Invisible Service Technicians, LLC Always select and press “Update IST Initial Setup” button to save modifications made to viewed section, if not when you select and move to other tabs the section will return to previous settings. Op Delay Name = Short name on board. Sensor= Digital or Thermo sensor used to trigger delay. State= Binary state of sensor to cause trigger of delay 1= closed 0= opened. Delay= Delay time in minutes. Op Delays are Dependent upon power being applied to one of the following: Y1, Y2, W1, W2 LED On = 0 LED Off = 9 LED Flashing = 10 Photo Cell Open = off NO = LED off Photo Cell Closed = on NC = LED on Outdoor Temperature Sensor: By default the OAT sensor is set to “Temp6”. The OAT sensor is used for on the board calculations of Heat days and Cool days. Flash Code 1 By default is set to Control 1 (Reader 1) Digital 5 Flash Code 2 By default is set to Control 2 (Reader 2) Digital 6 Set the Code 1 and Code 2 to the normal condition of LED General Tab: IST Maint SETUP

4 Copyright, 2006: Invisible Service Technicians, LLC Op Delays are Dependent upon power being applied to one of the following: Y1, Y2, W1, W2 Long Name: Displayed on Reports, and Data Center Short Name: Displayed on board Secondary min/max temperature 2 Lim Src = Digital, or Thermo source to trigger 2 min/max. 2 Lim Stat = Condition of source to cause trigger of 2 min/max. Delay = Source trigger delay in minutes. 2 min/max Delay and Op Delay work in parallel. They initiate at same time. Ability to Enable or Disable installed Temperature sensor. Indicates sensors that have been checked as installed on Data Center. Temp Sensors: IST Maint SETUP

5 Copyright, 2006: Invisible Service Technicians, LLC Op Delays are Dependent upon power being applied to one of the following: Y1, Y2, W1, W2 Dep 1 Src and Dep 2 Src Select options: Digital sensors (Digital1- Digital8) Thermo sensors (Thermo1- Thermo8) Conditional Logic for sensors: Dep * Staton, off Dep Opor, and Logic Statement includes: (Op delay, Dep 1 Src, Dep 1 Stat, Dep Op, Dep 2 Src, Dep 2 Stat) This statement has to be True before the initiation of alarm. Temp Sensors: IST Maint SETUP

6 Copyright, 2006: Invisible Service Technicians, LLC Op Delays are Dependent upon power being applied to one of the following: Y1, Y2, W1, W2 Thermo sensor inputs offer status of thermostat operating condition. Wiring is paralleled off thermostat terminal strip. (G,Y1,Y2,W1,W2,REV,E) Thermo sensors detect the presence of applied 24v + off T-Stat. If using a Thermo sensor to detect status from relay ensure that 24v+ is applied to input and that the voltage originates from same control transformer providing power to monitor. Must share same common. Thermo sensors must be wired and set to “Enabled NO” to trigger accumulator. Thermo. Sensors: IST Maint SETUP

7 Copyright, 2006: Invisible Service Technicians, LLC Op Delays are Dependent upon power being applied to one of the following: Y1, Y2, W1, W2 Thermo sensor status is immediately indicated by monitor, the delays and dependencies only affect output to Alarm. Spare Thermo sensor (Aux3) Enabled Enabled NO Enabled NC Disabled Thermo. Sensors: IST Maint SETUP

8 Copyright, 2006: Invisible Service Technicians, LLC Op Delays are Dependent upon power being applied to one of the following: Y1, Y2, W1, W2 Short Name: 8 characters, used on board. Long Name: 50 characters, used in Data center, & Reports. Enabled Flash Cde Det Enabled NO Enabled NC Disabled  When selecting “Flash Cde Det” for enabled condition you must perform the following:  Set normal conditions of LED “General” tab. o LED on = 0 o LED off = 9 o LED Flashing = 10  Flash code descriptions and alert condition (If alert is to be sent for 1 or all flash counts) “Data center”.  Enable alarm for specific Digital “Alarm” tab. Digital Sensors: IST Maint SETUP

9 Copyright, 2006: Invisible Service Technicians, LLC Op Delays are Dependent upon power being applied to one of the following: Y1, Y2, W1, W2 Digital sensors can be set to either “Enabled NC” or “Enabled NO” to trigger accumulator. Digital sensor status is immediately indicated by monitor, the delays and dependencies only affect output to Alarm. Digital Sensors: IST Maint SETUP

10 Copyright, 2006: Invisible Service Technicians, LLC Op Delays are Dependent upon power being applied to one of the following: Y1, Y2, W1, W2 Src 1, Src 2 Selections available are Temp sensors, and Calculations that have been defined with short Name. Operator Math functions available (Add, Subtract, Multiply, and Divide). 2 min/max Ability to apply 2 min/max temp values for alarm output. Enable or Disable Calculation Logic Statement These statements operate the same in all tab’s and must always be True before alarm is issued. Calculations: IST Maint SETUP

11 Copyright, 2006: Invisible Service Technicians, LLC Accumulators Accumulators track run minutes of applied source. Accumulated minutes are sent each transmission and reset to 0 on board after completion of transmission. Source Selections available are Digital and Thermo sensors. Accumulators: IST Maint SETUP

12 Copyright, 2006: Invisible Service Technicians, LLC Cycles This function counts the cycles (on / off) of source. Cycles are sent each transmission and reset to 0 on board after completion of transmission. Source Selections available are Digital and Thermo sensors. Cycles: IST Maint SETUP

13 Copyright, 2006: Invisible Service Technicians, LLC Primary min/max Temperatures Secondary min/max Temperatures 2 min/max Temps are triggered by Digital or Thermo sensors located in “Temp Sensor”, and “Calculation” sections. Min Max Alarm Enable or Disable Alarm output for both primary and secondary min/max temperatures. Alarm Section Alarm section is dependent on Logic statement for each sensor (device) being True before issuing alert. Refer to Calculations tab (last 5 options: Dep 1 Src, Dep 1 St, Dep Op, Dep 2 Src, Dep 2 St) Alarm Text Message Enable or Disable Text Message Alarms: IST Maint SETUP


Download ppt "Copyright, 2006: Invisible Service Technicians, LLC Invisible Service Technicians, LLC Invisible Service Technician Monitor Activation Process: IST MaintSelectionV3.php."

Similar presentations


Ads by Google