Download presentation

Presentation is loading. Please wait.

Published byMacey Gallop Modified over 3 years ago

1
BODY FITTED COORDINATES BFC grid for a rectangular to circular nozzle BFC grid type ‘O’ for na airfoil

2
DOCUMENTATION BFC phoenics online documentations: – Introduction, Introduction – Boundary Conditions and Boundary Conditions – GCV (general colocated velocity method) GCV Tutorials (look for BFC tutorials) Tutorials Browse at the phoenics input library cases for: BFC and Multblock

3
When To Use BFCs BFCs are particularly suitable for internal or external flows with smoothly-varying non-regular boundaries. For such flows, BFCs provide: – Good geometric representation, – Possibility of economical grid refinement close to the surface, – Good representation of surface boundary layers, and hence of wall friction and heat transfer. – BFCs can also be used to reduce numerical "false-diffusion" errors, by aligning the grid with the local flow direction where possible, e.g., for angled jets (inclined fan heater in a room)

4
BFC grids The task of the BFC grids is to map a physical domain into a cartesian computational domain. The actual areas and volumes are transmited into the computational domain by means of area and volume multipliers deduced from the physical domain.

5
Coordinate Systems Columns of cells must continue from one end of the grid to the other, i.e., the mesh is structured. The cells are counted using the same conventions as in Cartesian and polar geometries: 1 to NX in the IX-direction 1 to NY in the IY-direction 1 to NZ in the IZ-direction The grid corner points must be prescribed by the user, via a Cartesian frame of axes, (XC, YC, ZC). The alignment of the Cartesian axes - and the origin - can be chosen arbitrarily. NOTE: The Cartesian coordinates (XC,YC,ZC) must NOT be confused with the cell-indices (IX,IY,IZ). Note how the Cartesian and grid axes only coincide for the first few cells.

6
Structure of the Grid File XC, YC and ZC are the Cartesian co-ordinates of the nodes. Note that: I goes from West to East, J goes from South to North, and K goes from Low to High. I, J & K count nodes (cell corners), IX, IY & IZ count cells. NX, NY and NZ are the numbers of cells in the I (IX), J (IY) & K (IZ) directions. n o of nodes The total n o of nodes along x is NX+1, the same applies to the other directions. I=1 I=6 IX=5IX=1 EAST WEST

7
Velocity Components Q is the total velocity vector. U1, V1 (and W1) are the SOLVEd velocity resolutes. UCRT, VCRT (and WCRT) are the deduced vector components in the Cartesian coordinate system. UC1, VC1 (and WC1) are the deduced vector components in the grid line directions (the co-located velocities) IY IX

8
The Steps In BFC Grid Generation 1.Specify POINTS - provide the Cartesian coordinates of key features of the geometry to be meshed 2.Specify LINES - join the points by lines, which are divided into segments corresponding to the number of cells which lie along the line. Lines may be straight, arc segments, or spline curves through defined points. 3.Create FRAMES - link the lines to make 2-D FRAMES. Frames always have four corners. 4.MATCH Grid to Frames - match the grid plane to appropriate frames. 5.Form the 3-D Grid - link 2-D grid planes to form a 3-D grid.

9
POINTS LINES EACH LINE IS DIVIDED IN POINTS WHICH WILL FORM THE VOLUMES FORMING THE FRAMES EACH FRAME HAS ALWAYS 4 CORNERS EXTRUDING TO FORM VOLUMES SEE ADDITIONAL INFORMATION AT: Introduction,Introduction

10
WORKSHOP#1: SETTING A BFC GRID a.Set to view plane (XY); b.click on mesh togle; c.Select BFC grid Y X 510 5 5 DIMENSION: NX = 15 & NY = 10 The points cartesian coordinates are defined on the problem data sheetproblem data sheet * Edit your q1 file to Set points XPO= 0.0;YPO= 0.0;ZPO= 0.0; GSET(P,A) XPO= 4.0;YPO= 0.0;ZPO= 0.0; GSET(P,B)

11
WORKSHOP#1 – STEP2 Setting: points, lines, and number of nodes RESCUE Q1

12
WORKSHOP#1 – STEP2 ½ Setting: dimension, lines and cells RESCUE Q1 Dimension declares the total number of volumes along each direction. Set NX = 15 and NY = 10 * Edit your q1 file to Set lines/arcs GSET(L,L1,A,B,5,1.0) GSET(L,L2,B,C,10,1.0) GSET(L,L3,C,D,5,1.0) GSET(L,L9,B,H,5,1.0,ARC,1)

13
WORKSHOP#1 – Step 3 FRAMES always have 4 corners only Frame#1: corners GSET(F,F1,A,-,B,-,H,-,G,-) Frame#2: corners GSET(F,F2,B,-,C,-,D,-,H,-) Frame#4: corners GSET(F,F4,G,H,D,-,E,-,F,-) Number of Cells on each side of the Frame has to match!

14
WORKSHOP#1 – Step 3 Setting a Frame

15
WORKSHOP#1 – Step 4 Match a grid a.Pick the first corner of a Frame b.Match the corner with the NODES coordinates c.Specify the first corner direction to the next points. All frames have right-handed axes. Ex: B->C +I & C->D +J (I,J,K) (6,1,1) (I,J,K) (1,1,1) (I,J,K) (1,6,1) RESCUE Q1 * Match a grid mesh GSET(M,F1,+I+J,1,1,1,LAP5) GSET(M,F2,+I+J,6,1,1,LAP5) GSET(M,F4,+I+J,1,6,1,TRANS)

16
WORKSHOP#1 – Step 4 Match a grid

17
WORKSHOP#1 – Step 5 Volume a.Grid along (XY) plane b.To create volumes is necessary to extrude the grid along the K direction * Copy/Transfer/Block grid planes GSET(C,K2,F,K1,1,15,1,10,+,0,0,1,INC,1) GSET(C,pln2,F,pln1,i1,i2,i3,i4,+,dx,dy,dz,INC,pwr) shift grid plane by a distance and include the internal planes

18
Inlet Boundary Conditions It is a special b.c. because the mass fluxes are related to the U1, V1, W1 resolute and not to the UCRT, VCRT and WCRT. In general the required angles will vary from cell to cell. Subroutine GXBFC has been provided to calculate the inlet conditions automatically, for the case of uniform inflow. UCRT, VCRT, WCRT and density is non-standard, and simply provides a mechanism for transmission of UIN, VIN, WIN and RHOIN to GXBFC SEE ADDITIONAL INFORMATION AT: Boundary ConditionsBoundary Conditions

19
Use Of Cyclic Boundaries The default setting in PHOENICS is no cyclic conditions, and a symmetry condition is assumed. Cyclic (or periodicity) boundary conditions applies only along the east and west boundaries of XZ plane. The provision for BFCs is intended for turbomachine (and airfoil) applications in which cyclic conditions are needed at the entrance to and exit from the blade passage. To activate x-cyclic boundaries: Group 6, Q1 file: XCYIZ(1,NZ,T) (switches XCYCLE on for all IZ slabs) XCYIZ(1,9,T) (switches XCYCLE on for IZ=1 to 9) case B523 exemplifies the use of x-cyclic boundary conditions for the flow through a cascade of wedges

20
WORKSHOP#1: SET UP A CASE USING BFC Models: – elliptic GCV and, – solution for Vel & P – KECHEM Numerics: 200 iter. Props: Fluid: air(0) Create objects: – inlet size: (10,1,1) & -2 m/s, – outlet size (5,1,1) – blocakge. Note: case B116 has 15x15 volumes. inlet outlet plate RESCUE Q1

21
Real world is not so simple

22
Automatic Block Links The GCV solver uses overlapping cells at block joints. These cells must exist in the individual block grid files. Link automatic is when the blocks share the same IJK orientation and same number of cells

23
A Natural Link A natural link is when the blocks share the same IJK orientation but not the same number of cells B1 share the north face of L3 with the south face of B2 B2 B1 S N

24
Basic steps for Multi-Block Setup a.Plan the decomposition of domain into individual blocks. A possible configuration is shown. Block 1 is to be 5 x 15 x 1, and Block 2 is to be 15 x 5 x 1. b.Generate the grid for each individual block. The grid for each block will be generated in a separate mesh- generator session. c.Combine the grids to form the multi- block grid and define inter-block links. This step involves hand-editing the input Q1 file. d.Define remainder of the problem (variables, boundary conditions, etc). B2 B1

25
Block links a.The GCV solver uses overlapping cells at block joints. These cells must exist in the individual block grid files. b.Only the linked faces of a block require an extra layer of dummy cells. c.Block B1 has an extra plane of nodes at J =17 with thickness DY=0. d.Similarly B2 has an extra plane of nodes at J = 1 with thickness DY =0 e.These extra nodes are most conveniently copied exactly from the 'real' edge nodes, so that they are invisible to any viewing program. f.See further examples at GCVGCV (15,6) (16,5) J=1 J=16 J=17 DY=0 J=1 J=2 J=6 B2 B1

26
Linking the blocks in Q1 TALK=T; RUN( 1, 1) BFC=T NUMBLK=2 READCO(GRI+) MPATCH(1,MBL1-2, NORTH,1,NX,NY-1,NY-1,1,NZ,1,1) MPATCH(2,MBL2-1, SOUTH,6,10,2,2,1,NZ,1,1) STOP See additional information on linking blocks at GCVGCV (15,6) (16,5) J=1 J=16 J=17 DY=0 J=1 J=2 J=6 B2 B1 Y X

27
WORKSHOP#2 – Flow in a bifurcation; a natural link Each block’s grid is developed and then linked together.

28
WORKSHOP#2 - Flow in a bifurcation; We will follow the workshop on how to assemble natural links in a pipe bifurcation: wksh multiblock 1.wksh multiblock 1 To short the drilling time, please download the q1 file which contains the Points and Lines.q1 After UPLOADING the file start from section: ‘Set grid for first block’ on wksh multiblock 1. wksh multiblock 1 Block 2 Block 1

29
WORKSHOP#2 – Blocks’ construction; Hint: before building MGRID2 (left) erase: the volume, the frame and the cells of MGRID1 (right) leaving only the lines. Rescue q1 files at the links: MGRID1 and MGRID2.MGRID1MGRID2

30
WORKSHOP#2 – Assembling the case Rescue q1 files at the links: MGRID3, GRI1, GRI2. Save these files at your working directory.MGRID3GRI1GRI2

31
Unnatural Block Links Link is unnatural when the blocks do not share the same IJK orientation Y X B1 B2 B3 S N EW W N Blocks 1&2 and 1&3 are linked 'naturally' - West to East and South to north, whilst the link between 2&3 is 'unnatural' - a North face is linked to a West face. The instructions are in the tutorial: workshop multblock-2; also visit the links: READCO, MPATCH and link the three blocks.workshop multblock-2READCOMPATCHlink the three blocks E N E

32
Basic steps for Multi-Block Setup a.Plan the decomposition of domain into individual blocks. A possible configuration is shown above. Each block is to be 5 x 5 x 1. b.Generate the grid for each individual block. The grid for each block will be generated in a separate mesh-generator session. c.Combine the grids to form the multi-block grid and define inter- block links. This step involves hand-editing the input Q1 file. d.Define remainder of the problem (variables, boundary conditions, etc).

33
WORKSHOP#3 - Flow in a disk sector; We will follow the workshop on how to assemble un-natural links in a disk sector: workshop multblock-2 workshop multblock-2 To short the drilling time, please download the q1 file which contains the Points and Lines.q1 After UPLOADING the file start from section: ‘Set grid for first block’ on workshop multblock-2workshop multblock-2

34
WORKSHOP#3 – Blocks’ extrusion parameters UGRID1.q1 UGRID2.q1 UGRID3.q1 B1 B3 B2 W E N S W N B1 B2 B3 BLOCK # B1 B2 B3 Length plane plane plane from/to from/to from/to Direction K 1 to 2 1 to 2 1 to 2 dZ = 1 Direction J 6 to 7 6 to 7 2 to 1 dY = 0 Direction I 2 to 1 6 to 7 2 to 1 dX = 0

35
TALK=T;RUN(1,1) BFC=T GCV=T NUMBLK=3 READCO(UGRI+) MPATCH(1,MBL1.2,WEST,2,2,1,NY-1,1,NZ,1,1) MPATCH(2,MBL2.1,EAST,NX-1,NX-1,1,NY-1,1,NZ,1,1) MPATCH(1,MBL1.3,NORTH,2,NX,NY-1,NY-1,1,NZ,1,1) MPATCH(3,MBL3.1,SOUTH,2,NX,2,2,1,NZ,1,1) MPATCH(2,MBL2.3,NORTH,1,NX-1,NY-1,NY-1,1,NZ,1,1) MPATCH(3,MBL3.2,WEST,2,2,2,NY,1,NZ,1,1) SPEDAT(SET,GCV,MBL3.2,C,WNL) STOP B1 B3 B2 W E N S W N If the blocks are rotated relative to each other in IJK space (B3 to B2), the block alignment must be specified through SPEDAT command.SPEDAT This string defines how the N, E and H faces of the first block link to the second block. The default, natural, link would be S W L; i.e. North to South, East to West and High to Low, see B1 to B3 and B2 to B1. WORKSHOP#3 - Matching Blocks q1 code lines

36
The string defining the block rotation consists of three letters, which may be any of E W N S H L. The individual characters define the relative orientation between the N, E and H faces of the first block (B2) of the pair of blocks, and the current block (B3) respectively. B1 B3 B2 W E N S W N y x x y E W N S B3 N S W E B3 is rotated 90º from B2 Blocks’ Linkages WORKSHOP#3 - SPEDAT COMMAND & BLOCK ROTATION SPEDAT(SET,GCV,MBL3.2,C,WNL) BLOCK#2 -> N E H BLOCK#3 -> W N L B3 N S W E

37
WORKSHOP#3 – Case setting; Properties: air (0) Model: laminar, activate velocities, CGV Numerics: 100 iteractions Objectcs: Inlet (V = 1,0 m/s) & Outlet

38
WORKSHOP#3 – Results Rescue q1 files at the links: UGRID123, UGRI1, UGRI2, UGRI3. Save these files at your working directory.UGRID123UGRI1UGRI2UGRI3

39
Multblock Application in Complex Geometry The selected figures come from the cases available in the phoenics input library ( Multiblock)

40
Phoenics BFC Generator The Phoenics built-in BFC Generator is helpful for simple problems. If an application demands several ‘natural or unnatural’ links the mesh generation process becomes very complex. In this scneario phoenics BFC generator is not recommended. There are specific software for mesh generation recommended such as: ICEM,ICEM

41
This is a ‘O’ type grid where the airfoil upper section is mapped into the computational domain for reference. Physical Domain Computational Domain Airfoil Grids: ‘O’ grid

42
Airfoil Grids: ‘C’ grids http://courses.cit.cornell.edu/fluent/airfoil/step1.htm The domain size is expressed in terms of the airfoil thickness. Airfoil with finite thickness (present illustration) require Natural and/or Unnatural links, unfortunately. It is not an easy task to do using Phoenics BFC grid generator!

43
C Grids for Finite Thicknes Airfoil ( represent the frames’ corners) Blocks B1, B2, B3 have natural links B4 is 180o rotated in regard to B1. Multi Block grid. Provide extra Y cells to B1 and B4 SPEDAT(SET,GCV,MBL4.1,C,NEL) (A)(B) (C) (D) (E)(F) (G) (H)(L) B1 B2 B3B4 x y x y x y x y zero thickness trailing edge B1B2 B3 (A)(B) (C) (D) (E)(F) (G) (L) B4 finite thickness trailing edge Blocks B1, B2, B4 have natural links B3 is 180o rotated in regard to B4. Multi Block grid. Provide extra Y cells to B4 and B3 SPEDAT(SET,GCV,MBL4.3,C,NEL)

44
Finite x Small Thickness Airfoil The small thickness airfoil is gives an approximated solution. The thin airfoil consists of a line and it is easily setup on the BFC mesh generator in phoenics.

45
Natural links for airfoil: frames

46
Natural links for airfoil: grid This grid would be a 2 nd choice for the C grid. It still can be improved by changing the inclination of lines L23 & L24 an designing a better number of cells to result in a more orthogonal mesh. One can also design a similar grid for a zero thickness airfoil

47
Axis symmetric flow in a sector Choose the XY plane to work Set NX = 20, NY = 10 and NZ = 1 Once a XY frame is done a copy of it will be made rotating x axis by 1 rad (57º)

48
Set Points – GSET, GSET(P,…)PGSETGSET(P,…) PXYZ A000 B1000 C 10 D9 0 E640 G010 B A C E D G * Edit your q1 file to Set points XPO= 0.000000E+00;YPO= 0.000000E+00;ZPO= 0.000000E+00;GSET(P,A ) XPO= 1.000000E+01;YPO= 0.000000E+00;ZPO= 0.000000E+00;GSET(P,B ) XPO= 1.000000E+01;YPO= 1.000000E+01;ZPO= 0.000000E+00;GSET(P,C ) XPO= 9.000000E+00;YPO= 1.000000E+01;ZPO= 0.000000E+00;GSET(P,D ) XPO= 6.000000E+00;YPO= 4.000000E+00;ZPO= 0.000000E+00;GSET(P,E ) XPO= 0.000000E+00;YPO= 1.000000E+00;ZPO= 0.000000E+00;GSET(P,G )

49
Set Lines/arcs – GSET(L,…)LGSET(L,…) * Edit your q1 file to Set lines/arcs GSET(L,L1,A,B,10,1.0) GSET(L,L2,B,C,10,1.0) GSET(L,L3,C,D,10,1.0) GSET(L,L4,D,G,20,1.0,ARC,E) GSET(L,L5,G,A,10,1.0) Number of volumes Grid Power L2 L1 L3 L4 L5 B A C E G D

50
Set Frames – GSET(F,…)FGSET(F,…) * Edit your q1 file to Set frames GSET(F,F1,A,B,C,-,D,-,G,-)

51
MMatch a frame – GSET(M,…)GSET(M,…) * Edit your q1 file to Set frames GSET(F,F1,A,B,C,-,D,-,G,-)

52
CCopy/Transfer/Block grid planes– GSET(C,…)GSET(C,…) * Copy/Transfer/Block grid planes GSET(C,K2,F,K1,1,20,1,10,RX,1,0,0,INC,1)

53
Inlet Outlet plate Inlet: set an inflow of 1m 3 /s Properties: Air (0) Model: GCV + LVEL (turbulence) Numerics: 500 Edit Objects Rescue q1

Similar presentations

Presentation is loading. Please wait....

OK

Engineering Mechanics: Statics

Engineering Mechanics: Statics

© 2018 SlidePlayer.com Inc.

All rights reserved.

To ensure the functioning of the site, we use **cookies**. We share information about your activities on the site with our partners and Google partners: social networks and companies engaged in advertising and web analytics. For more information, see the Privacy Policy and Google Privacy & Terms.
Your consent to our cookies if you continue to use this website.

Ads by Google

Ppt on changes around us class 6 Ppt on sub soil investigation Ppt on history of national flag of india Ppt on event driven programming pdf Ppt on network topologies Ppt on inhabiting other planets in the milky Download ppt on mobile operating system Ppt on neil bohr model of atom Mp ppt online form 2012 Ppt on non ferrous metals and alloys