We think you have liked this presentation. If you wish to download it, please recommend it to your friends in any social system. Share buttons are a little bit lower. Thank you!
Presentation is loading. Please wait.
Published byBailey Lane
Modified over 3 years ago
OD GEAR PITTING IN 12 MTR BUS
OD GEAR PITTING 12 MTR BUS
PROPELLER SHAFT CHECK NUT WRONG FITMENT
FRONT HUB BRG CONE ROTATION FA99
SOCKET TYPE DRAGLINK FAILURE IN 12MTR BUS
CLUTCH FINGER WEAR 15 RDC AND RETAINER SPRING CUT
CLUTCH RELEASE BRG HUB DIGGING RDC 15
12MTR BUS 205HP PISTON CRACK WITHIN 1.3 LAC.
PISTON OIL RING FAILURE 205 HP ENG. 12 MTR BUS
UJ CROSS FAILURE IN 3123H
KINGPIN SHIM CUT IN FA90 AND FA99
CROWN PINION PILOT BEARING PITTING AT 1.5 LAC KM.
SINCRO CONE AND RING WEAR FOUND WITHIN 1 LAC. KM IN 3121H MODEL AND 12MTR CRS
MAIN SHAFT BEARING WEAR FOUND WITHIN 1 LAC. KM IN 3121H MODEL AND 12MTR CRS
INPUT SHAFT BEARING WEAR FOUND WITHIN 1 LAC. KM IN 3121H MODEL AND 12MTR CRS
ACCL- PADEL WIRING HARNES LOOSE CONNECTION
FUEL METERING UNIT PIN BACKOUT
24VOLT ECU CONNECTION SUPPLY LINE PIN BACKOUT FROM BATTERY SIDE
LOOSE CONTACT PINS WITH FEMALE CONNECTER
CYLINDER 1 SPECIFIC ERROR : SHOT CIRCUIT LOW SIDE TO HIGH SIDE
MISSING OF DIAGNOSTIC SOCKET AND WATER SEPRETOR SOCKET
3123 VHICLE SPEED SENCER WRONG FITMENT : F8842700 INSTAD OF F8842800
Clutches Basic purpose Used to disengage engine from input shaft Flywheel –Bolted to crankshaft –Provides surface for clutch disc to work on Clutch disc.
1000A 60Hz Gearbox Grade 3 Incoming Inspection Serial Number: (BR) TGW Job Number: Inspection Date: 1/14/13 1.
Clutch Replacement & Inspection Be sure to mark the Pressure Plate to Flywheel orientation. Loosen bolts in sequence 1/2 turn at a time to prevent warpage.
SERVICING CLUTCHES l Chapter 3 l Page 49 l Lab manual l Page 45 l Classroom Manual.
Note location of different length bolts
SERVICING CLUTCHES Chapter 3 Page 49 Lab manual Page 45
Clutch Fundamentals Chapter 69.
1000A 60Hz Gearbox Grade 3 Incoming Inspection Serial Number: TGW Job Number:A Inspection Date:5/4/11 1.
New Mexico FFA Agricultural Mechanics Career Development Event Engine Power.
PISTON ENGINE PROPULSION Chapter 1 Mechanical Arrangement 1933 Alvis Engine 2014 Hyundai Engine.
KSRTC CENTRAL WORKS PRESENTED BY GEORGE JOSE 8214.
Clutch Automotive clutch is used to connect and disconnect the manual transmission from the engine.
1 Steering Going in the right direction. 2 Steering systems Conventional (parallelogram) Rack & Pinion Electronic (new in 2002) steer by wire Audi/Volvo.
The art of Engineering TURBINE PARTS. The art of Engineering TURBINE PARTS Valve Parts A. Stems, Disc, Seats B. Crosshead Assembly, Crosshead Bushings,
Starting Systems State a major safety precaution when removing or working around a starting motor.
Manual Transmission Components and Operation
© 2012 Delmar, Cengage Learning Starting System Service Chapter 29.
COMPANY INTRODUCTION A Swaraj enterprise is one of the leading tractor brands in the world. It is also the largest manufacturer of tractors in India with.
Components/purpose (Terminology) Engine Flywheel – keeps the engine running smoothly but also provides a flat smooth surface that the Centre Plate is pushed.
Engine Construction Stationary Parts 2 s/c Slow Speed BEDPLATE LUBE OIL SUMP A FRAME CYLINDER BLOCK JACKET WATER CYLINDER LINER CYLINDER HEAD INTAKE PORTS.
Clutches Auto 3/4 Mr. Saunders GO 12/2001VHS AUTO3 Who needs a clutch?
1 Product Immersion Olathe June FS 4800 Available as a front pivot (Standard) or rear pivot model 900mm (36”) Maximum Blade Capacity 35.7 kW (48.
Flat Saw Training. Flat Saw Sizes –Low Horsepower Blade diameters range from 8” (200mm) to 18” (450mm) Power ranges from 4 to 25 horsepower.
Engine Technology Engine Diagnostic its requires an understanding of the fundamentals & a systematic approach to determine what the problem is. If the.
Manitoba School Bus Pre-Trip Inspection
© 2015 Cengage Learning. All Rights Reserved. May not be scanned, copied, duplicated, or posted to a publicly accessible website, in whole or in part.
Valve train inspection Inspect... Cylinder head castings Valves Guides Springs Cam and lifters Rocker arms and push rods Timing chains and gears Copyright.
Common starting system problems. n n In a no-crank problem, the engine crankshaft does NOT rotate properly with the ignition key at start. The most common.
How Differential works
© Unitec New Zealand 1 Faulty Starting System Symptoms No Cranking Slow Cranking Abnormal Noise Overheating of Cables.
Model OutlineBodyBody ElectricalEngineChassis Contents Click a Section Tab.
1 of 26 Automatic Transmission Components and Operation This presentation will explore: Automatic Transmission System Layout Torque Converter Construction.
Automotive Chassis Systems, 5/e By James D. Halderman Copyright © 2010, 2008, 2004, 2000, 1995 Pearson Education, Inc., Upper Saddle River, NJ All.
PVWH Pump Presentation. PVWH Pumps n 10 Displacements –. 66 in³/rev –.86 in³/rev –1.35 in³/rev –1.55 in³/rev –2.06 in³/rev –2,83 in³/rev –3,88 in³/rev.
Chapter 6 Light vehicle chassis systems © Pearson Education Ltd Copying permitted for purchasing institution only. This material is not copyright.
Steering Systems Chapter 44.
© 2012 Delmar, Cengage Learning Manual Transmission Diagnosis and Repair Chapter 72.
Differential Casting An epic look into the differential casting By: Scott Loughran.
1 InnoSys Quick Connect End Effecter Service and Maintenance Procedures Nov. 19, 2007 Rev. B.
Lesson 31 Main Engine Repair (II). 1. Crankpin bearing overhaul 2. Fuel pump removal & re-installation 3. Cylinder head removal/replacement 4.
1 Power Transmission System Presentation IKCO Samand.
PISTON ENGINES Part 6 Piston Engine Operations (Ignition)
© 2017 SlidePlayer.com Inc. All rights reserved.