Presentation is loading. Please wait.

Presentation is loading. Please wait.

TR6850 TR-6850 256 33MHz,8M pattern 16 / Visual Studio.NET C++

Similar presentations


Presentation on theme: "TR6850 TR-6850 256 33MHz,8M pattern 16 / Visual Studio.NET C++"— Presentation transcript:

1 TR6850 TR MHz,8M pattern 16 / Visual Studio.NET C++

2 System Architecture Up to 8-Site Parallel Testing Cable Out Maximum 256 Logic I/O Channels High Precision Measurement Unit Arbitrary Waveform Generator Digitizer Low Cost Mixed Signal Tester

3 System Architecture Test Head Architecture Analog Module PC Interface Digital Module

4 Targeted Applications For Digital, Analog and Mixed Signal Device MCU, Interface / Driver … Digital Chip AD Converter, DA converter Voltage Comparator Operational Amplifier Regulator – Shunt/Voltage Regulator, LDO…

5 Targeted Applications Hall Sensor PWM Switching, PWM Controller Power Factor Control IC DC to DC converter Detector, Voltage Detection MOSFET

6 Electrical Specifications AC64/AC32 – 64 /32I/O Channels Board Pin Configuration( I/O Channel) : 64 /32pins Parametric Measurement Unit : 4 Sets ( 8-pin share) Pin Level Source : Per pin level set Driver Voltage Range : -2.0V to +8V Comparator Voltage Range : -2.0V to +8V Min. Pulse Width : 10ns Micro Instruction : CALL, MATCH,MPAT,MLEN RPT,LOOP,LPEND,STOP,TS

7 Electrical Specifications AC64/32 – 64/32 I/O Channels Board – continue Min. Period : 30ns ~ 40ms Period resolution : 10ns Data Rate : 33MHz Timing Generators : 4 edge / Pin Timing Set : 16 change on the fly Edge Placement resolution : 2.5ns Time Measurement Resolution : 10ns

8 Electrical Specifications AC64/32 – 64/32 I/O Channels Board – continue Drive Mode : 0,1,NF,NRZ,RZ,RO,SBC IO Mode : 0,1,NF Strobe Mode : Edge/Window Pattern Memory Depth : 4M~8M Fail Memory Depth : 4K Pattern Symbol : 0/1//X/Z/L/H

9 Electrical Specifications OVC -- Octal V/I Resource Board Voltage Force and Measure Range 20V,16V 8V 4V 2V Voltage Force and Measure Resolution 16 bits Voltage Force and Measure Accuracy 2V ±(0.01 % of value+0.05 % of range ) 4V ±(0.01 % of value+0.05 % of range ) 8V ±(0.01 % of value+0.05 % of range ) 16V ±(0.01 % of value+0.05 % of range ) 20V : ±(0.01 % of value+0.05 % of range ) Voltage clamp Resolution 16 bits Current Force and Measure Range 1uA 10uA 100uA 1mA 10mA 100mA 200mA Current Force and Measure Resolution 16 bits

10 Electrical Specifications OVC -- Octal V/I Resource – continue Current Force and Measure Accuracy 1uA ±(0.2 % of value+0.2 % of range ) 10uA ±(0.1 % of value+0.1 % of range ) 100uA : ±(0.1 % of value+0.1 % of range ) 1mA : ±(0.1 % of value+0.1 % of range ) 10mA : ±(0.1 % of value+0.1 % of range ) 100mA ±(0.1 % of value+0.1 % of range ) 200mA : ±(0.1 % of value+0.1 % of range ) Current Clamp Resolution 16 bits 10KSPS DDS programmable to any Channel(16 bit) 10KSPS Digitizer multiplexed to two channels(16 bits) DVM Differential voltage measure between two channels

11 Electrical Specifications PVC -- Pulse Mode V/I Resource 2 Independent V/I Resource Floating Ground Pulse Mode Programmable Pulse period Protection Timer Voltage Force and Measure Range 4V 8V 16V 32V 46V Voltage Force and Measure Resolution 16 bits Voltage Force and Measure Accuracy 8V ±(0.3 % of value+0.15 % of range ) 16V ±(0.3 % of value+0.15 % of range ) 32V ±(0.3 % of value+0.15 % of range ) 46V ±(0.3 % of value+0.21 % of range )

12 Electrical Specifications PVC -- Pulse Mode V/I Resource – continue Current Force and Measure Resolution 16 bits Current Force and Measure Accuracy 150mA : ±( 0.5% of value+0.25 % of range ) 300mA : ±( 0.5% of value+0.25 % of range ) 1.5A ±( 0.5% of value+0.25 % of range ) 3A : ±( 0.5% of value+0.25 % of range ) 5A : ±( 0.5% of value+0.25 % of range ) 10A : ±( 0.5% of value+0.25 % of range ) 15A : ±( 1.0% of value+0.25 % of range ) 30A : ±( 1.0% of value+0.25 % of range )

13 Electrical Specifications DVC -- Full Four-Quadrant V/I Source Voltage Force and Measure Range 1V, 2V, 4V, 8V,16V, 32V, 48V Voltage Force and Measure Resolution 16 bits Voltage Force Accuracy ± (0.05 % of value+0.05 % of range) Voltage Measure Accuracy ± (0.03% of value % of range) Current Force and Measure Range 2uA 20uA 200uA 2mA 200mA, 1A, 2A

14 Electrical Specifications DVC -- Full Four-Quadrant V/I Source – continue Current Force and Measure Resolution 16 bits Current Force and Measure Accuracy 2uA ~ 200uA ± (0.05 % of value+0.05 % of range +10nA ) 2mA~ 200mA ± (0.1 % of value+0.1 % of range) 1A~2A : ± (0.3 % of value+0.1 % of range) Differential voltage measure between two channels Measure Resolution : 16 bit Measure accuracy: ±(0.2 % of range + 200uV) 20mV, 100mV, 200mV, 1V, 2V, 4V, 10V, 20, 100V

15 Electrical Specifications Arbitrary Waveform Generator – continue Pin Counts Per Module 2 4 Single-ended or 2 Differential. Resolution 16 Bits. Sampling Rate 40M SPS max 625k SPS min Waveform Memory 4M. Output Range ohm load a high-impedance load Accuracy : ±0.1dB DC Offset Range ohm load Accuracy :±5mV

16 Electrical Specifications Arbitrary Waveform Generator - continue Harmonic products ans spurs : –75 dBc Output Impedance 50 ohm 75 ohm. Filter Analog, 2MHz, 500kHz, 50kHz, 5k, Through. TTL Rising edge PW 40ns min. SYNC Output TTL Duty Cycle 20% to 80%. Marker Output TTL 8 Sample clock periods. Frequency Range 1Hz ~ 1MHz

17 Electrical Specifications Digitizer Input -3dB Freq. : 1Mhz 16bits (Low Speed: 500Ksps)/ 14bits (High Speed 10Msps) 4 single or 4 differential-end channels Output: 50 ohm Load to GND MEM Depth: 4M*16bits/channel Anti-Filter: 20kHz, 200kHz, 2Mhz Notch Filter: Notch freq. ~1Khz for audio testing. Digital Filter: 2x, 4x, 8x, 16x, 32x, 64x decimation filter. User Offset: ±2.0V Input Impedance: 50ohm, 1Mhz common ground or 100ohm, 10kohm differential.

18 Electrical Specifications Digitizer - continue PGA ranges: Single ended: ±0.1, ±0.5, ±1, ±2, ±5, ±10 Differential: ±0.05, ±0.1, ±0.25, ±0.5, ±1, ±2.5, ±5 Dynamic Performance (1kHz -1dBFS test tone with 2x decimation filter) THD: < -80dBc SNR: > 80dBc THD+N: < -80dBc Dynamic Performance (1kHz -1dBFS test tone with Notch filter) THD: -105dBc SNR: 99dBc THD+N: -98dBc

19 Electrical Specifications TMU -- Time Measure Unit Positive/Negative Slope. Counter Time measurement Rising/Failing time. Time Resolution 625ps Propagation delay Timeout function and Overflow state. Input waveform Sine square sawtooth. Low Impedance Inputs : A, B ±10V Range Impedance 2K/1M Ohm Nominal ±2.5V Range Impedance 2K/1M Ohm Nominal Input Threshold Accuracy 0.5% of Range

20 Electrical Specifications OP-LOOP Board Four OP AMP Loop DC Measurement 16 bits Common Mode DAC 16 bits AC Stimulus 16 bits High Speed DAC AC measurement 12 bit ADC 10MHz Sample Rate Loop Reference DAC 16 bits Input Offset voltage (Vos) Input Offset Current (Ios) Open loop gain (Avol)

21 Electrical Specifications OP-LOOP Board -- continue Command Mode Rejection Ration (CMRR) Power Supply Rejection Ration (PSRR) Gain Bandwidth Product (GBW) Slew Rate (SR)

22 Electrical Specifications KVS board: 2 Channels Floating Ground System 16bit ADC for voltage and current measure 16 bit DAC for voltage and current force Vmax: 900V Imax: 15mA Vrange : 100V, 200V, 500V,1000V accuracy: ±(0.05% of value % of range) Irange: 15uA, 150uA, 1.5mA, 15mA accuracy:±(0.05% of value % of range) Time Max : 10 sec

23 Electrical Specifications QVC board : Four Independent, Full Four-Quadrant VIs; Voltage to ±45V, Current to ±1A Voltage ranges 1, 2, 4, 8, 16, 32, 45 vlots; Current ranges 2uA, 20uA, 200uA, 2mA, 20mA, 200mA, 1A; 16 bits force and measure resolution; Measure V without forcing;

24 Electrical Specifications QVC board : Voltage Force Forcing Resolution16bits Force Accuracy ±(0.05% of value % of range) Voltage Measure Measure Resolution16bits Measure Accuracy ±(0.05% of value % of range)

25 Electrical Specifications QVC board : Current Force Forcing Resolution16bits 2uA Range Accuracy ±(0.1% of value + 0.1% of range + 10nA) 20uA – 1A Range Accuracy ±(0.1% of value + 0.1% of range) Current Measure Measure Resolution16bits 2uA Range Accuracy ±(0.1% of value + 0.1% of range + 10nA) 20uA – 1A Range Accuracy ±(0.1% of value + 0.1% of range)

26 Electrical Specifications MVC board : Full Four-Quadrant V/I Channel:2 Max. Voltage:100V ~ -45V Max. Current :500mA / Voltage Ranges100V, 50V, 32V, 16V 8V 4V Voltage Force Accuracy± (0.05 % of value+0.1 % of range) Voltage Measure Accuracy± (0.05% of Value +0.1 % of range)

27 Electrical Specifications MVC board -continue: Voltage Clamp Resolution16 bit Current Range2uA, 20uA, 200uA, 2mA, 20mA, 200mA, 500mA Current Force Accuracy: 2uA ~ 200uA ±(0.1 % of value+0.2 % of range +10nA ) 2mA~ 200mA ±(0.1 % of value+0.2 % of range) 500mA : ±(0.1 % of value+0.2 % of range) Current Measure Accuracy: 2uA ~ 200uA ±(0.1 % of value+0.2 % of range +10nA ) 2mA~ 200mA ±(0.1 % of value+0.2 % of range) 500mA : ±(0.1 % of value+0.2 % of range) Current Clamp Resoulation16 bit

28 Electrical Specifications MFB ( 8 channel ) Ramp force accuracy 4V Range : 1mV 12V Range : 2.5mV Measure accuracy: 4V range none filter : 1mV 10 range none filter : 2.5mV 4V range with filter : 2.5mV 10 range with filter : 5mV AWG sample rate : 64K length Digitizer Sample rate : 64K length AWG & Digitizer loop back testing : > 70dB SDIO function : Sample Rate 1Mbps {A,B}, {C,D},{E,F},{G,H} combination for data, clk signal.


Download ppt "TR6850 TR-6850 256 33MHz,8M pattern 16 / Visual Studio.NET C++"

Similar presentations


Ads by Google