# The Gordon Schools Graphic Communication Technical Department.

## Presentation on theme: "The Gordon Schools Graphic Communication Technical Department."— Presentation transcript:

The Gordon Schools Graphic Communication Technical Department

Cut Cylinder The views show the Front Elevation and part Plan of a cut Cylinder

Finding position of End Elevation
Draw the outline of the End Elevation. The dimensions for the End Elevation should be projected from the Elevation and Plan.

Finding Generators on Plan
Divide the Plan into 12 areas by using 30o and 60o lines. 12 11 1 10 2 9 Number each of the points found 3 8 4 7 5 6

Drawing Generators onto Elevation
Project each of the points from the Plan onto the Elevation base. 1 2 9 8 7 6 5 4 3 Number each of the points on the Elevation making sure that the numbers correspond with those on the Plan. 9 10 11 12 1 2 3 8 7 6 5 4

Drawing Generators onto End Elevation
Repeat the previous process for the End Elevation. 1 2 9 8 7 6 5 4 3 10 11 12 Make sure that the numbers used are correct and that they correspond to the numbers used on the Elevation and the Plan. 7 6 8 9 10 11 5 4 3 2 1 12

Finding points for cut surface on End Elevation
Project where the generators on the Elevation cross the cut line of the Cylinder over to the correct lines on the End Elevation. 1 2 9 8 7 6 5 4 10 11 12 3 3 Indicate each of the found points with a small dot. 6 7 5 8 4 9 3 10 2 11 1 12

Drawing cut surface on End Elevation
Draw a smooth curve through each of the 12 points found. 1 2 9 8 7 6 5 4 3 10 11 12 Darken the outlines of the End Elevation. If the Cylinder is solid the End Elevation will require the cut surface to be cross hatched. 6 7 5 8 4 9 3 10 2 11 1 12

Development of Cylinder (1)
Draw a base line for the Development. If possible make this line level with the base line of the Elevation and End Elevation. 1 2 1 2 9 8 7 6 5 4 3 1 2 Draw a line to indicate where the first generator of the Development will go. Step off the distance from each of the points on the Plan onto the Development base line.

Development of Cylinder (2)
Draw generators through each of the points found. 1 2 1 1 1 Number each of the generators. Choose carefully where to cut the Cylinder. It is normal to choose to cut the Cylinder on either the longest or the shortest generator. 1 2 9 3 8 4 7 5 6 9 1 1 1 1 2 1 2 7 8 9 1 1 1 9 10 11 12 1 2 3 4 5 6 7 8 9 8 7 6 5 4 3 6 5 4 3 2 1 1 2

Development of Cylinder (3)
Transfer each of the points from the generators on the End Elevation onto the correct generators on the Development. 1 2 9 8 7 6 5 4 3 Indicate each of the points with a small dot. 9 8 7 6 5 4 3 2 1

Development of Cylinder (4)
Draw a smooth curve through each of the points found on the Development. 1 2 9 8 7 6 5 4 3 Darken the outlines of the rest of the Development 9 1 1 1 1 2 1 2 3 4 5 6 7 8 9

True Shape of cut (1) 9 10 11 12 1 8 7 6 5 To draw the True Shape each of the points need to be projected away from the cut on the Elevation at right angles. 2 4 3 9 1 2 8 7 6 5 4 3 Draw a datum line to show where the True Shape will be positioned – in this case the centre line has been used. 9 1 8 7 2 6 5 4 3 9 8 7 6 5 4 3 2 1 Number each of the points for the True Shape.

True Shape of cut (2) 9 1 8 7 2 6 5 4 3 Measure the distance on the Plan from the centre line to each of the points of the cut surface. Transfer each of these points onto the True Shape. Mark each of the points found with a small dot. 1 2 1 1 1 1 2 9 3 8 4 7 5 6 9 8 7 6 5 4 3 2 1 9 1 1 1 1 2 1 2 3 6 7 8 9 1 1 1 8 7 6 5 4 5 4 3 1 1 2 2

True Shape of cut (3) 9 1 8 7 2 6 5 4 3 To finish the True Shape draw a smooth curve through each of the points found. 1 2 1 1 1 This is the final drawing. 1 2 9 3 8 4 7 5 6 9 8 7 6 5 4 3 2 1 9 1 1 1 1 2 1 2 3 6 7 8 9 1 1 1 8 7 6 5 4 5 4 3 2 1 1 2