We think you have liked this presentation. If you wish to download it, please recommend it to your friends in any social system. Share buttons are a little bit lower. Thank you!
Presentation is loading. Please wait.
Published byRyan Spencer
Modified over 2 years ago
MAINTENANCE GUIDE SOCKET LAYOUT ………………………………..p2 SOCKET IDENTIFICATION …………………..p3 SOCKET ASSEMBLED ………………………….p4 ~p7 CONTACTS REMOVAL …………………………p8 UPPER ELASTOMER REPLACEMENT …….p9 LOWER ELASTOMER REPLACEMENT ……p10 CLEAN …………………………………………….p11~12 REPLACEMENT FREQUENCY ……………….p13 Teecons Patent: US
SOCKET LAYOUT Teecons 2
SOCKET IDENTIFICATION Teecons 3
SOCKET ASSEMBLED STEP 1: INSERT LOWER ELASTOMER TO BOTTOM SIDE OF CONTACTS HOUSING STEP 2: REVERSE CONTACTS HOUSING AND PLACE ON SUPPORTER Teecons 4
STEP 3: INSERT CONTACTS TO SLOT OF CONTACTS HOUSING AND PUSH INTO LOWER ELASTOMER Teecons 5
STEP 4: INSERT UPPER ELASTOMER TO GUIDE PLATE STEP 5: ASSEMBLE GUIDE PLATE AND CONTACTS HOUSING Teecons 6
STEP 6: GROUND MODULE INSTALLATION (OPTIONAL) Teecons LIGHT PRESS INSERTION 7
CONTACTS REMOVAL Teecons 8
UPPER ELASTOMER REPLACEMENT ELASTOMER REMOVAL ELASTOMER INSERTION Teecons 9
LOWER ELASTOMER REPLACEMENT ELASTOMER REMOVAL ELASTOMER INSERTION Teecons 10
CLEAN CLEAN TOOL (OPTIONAL) CLEAN BLOCK HANDLE Teecons 11
CLEAN PROCEDURE ON-LINE CLEAN CLEAN FREQUENCY -- 10K UP/DOWN TIMES Teecons 12
REPLACEMENT FREQUENCY (RECOMMENDATIONS) 1CONTACTS500K 2CONTACTS HOUSING1.5kk 3UPPER ELASTOMER200K 4LOWER ELASTOMER800K 5GUIDE PLATE500K 6GND MODULE1kk Teecons 13
Process Instrumentation Mounting Installations SITRANS P1 of 15/ 09/ 02 Process Instrumentation and Analytics Mounting Installations SITRANS P for Differential.
RP-500 ½- 1. Modification Overview Production of the RP500 began in 2007 and is current. Production of the RP500 began in 2007 and is current.
Sectional Assembly and Installation. Sectional Assembly & Installation Items Needed for Installation 1)6D Galvanized Screws 2)Silicone 3)1 ½ x 1 ½ x 3.
Ranger Explorer Operations Guide ELearning Module Ver
Step-by-Step: Insert and Remove a Manual Page Break USE the document that is open from the previous exercise. 1.Delete all blank lines above Proposal Description.
HP Printer Paper Jams HP Printer Paper Jams 8000 Series OIT lab services.
Construction of a regular pentagon Dr Andrew French Const. Pent. p1 of 10. A.French 2012.
© 2011 Eaton Corporation. All rights reserved. M-Max Training Tom Neuberger – Product Manager VFD’s.
Euratom Mechanical operation on the TPL sector E.Delmas – December 8th /13 Disassembly and reassembly of a sector of the Toroidal Pumped Limiter.
Geometry Introduction. Topic Introduction Two lines Intersection Test Point inside polygon Convex hull Line Segments Intersection Algorithm.
FRONIUS IG Display Simulation © Fronius 2006 The following slides introduce how to set up a Personal Display with a FRONIUS IG inverter. Please note that.
Slide 1 Insert your own content. Slide 2 Insert your own content.
Setup/Operating/Maintenance Procedures ICRI/2P A tactical radio/telephone interoperability gateway As configured for the Federal Air Marshal Service Under.
LQ Reaction & Impregnation Tooling Internal Review F. Nobrega, N. Andreev May 7, 2007.
Step-by-Step: Insert a Section Break USE the document that is open from the previous exercise. 1.Scroll up to page 1 and position the insertion point after.
Woodwork Joints 2. Dowel Joint Dowel Jig Dowel joints have now replaced many traditional joints in factory made furniture where holes can be drilled accurately.
Principles of Agricultural Science – Animal 1. 2 Using a Syringe Principles of Agricultural Science – Animal Unit 8 Animal Health Lesson 8.4 Pathogens.
Ladle Gate Type LS. Casting with the Ladle Gate LS.
LTL-X RETROMETER OPERATION AND MAINTENANCE. THE LTL-X RETROMETER.
UnFramed Canopy Fitting Instructions V3.0 Contents – 1 x handle pack 12 x 30mm Wood Screws 4 x M8 flat washers 3 keys 1x door 4 x M8 - 50mm coach screws.
Computer Graphics 4: Viewing In 2D. * Windowing Concepts Windowing Concepts *ClippingClipping ◦ Point Clipping Point Clipping ◦ Line Clipping Line Clipping.
Tagger and Vacuum Chamber Assembly Procedure. Outline. Assembly procedure for tagger and vacuum chamber. Support stands. Alignment.
Maple Valley Fire LZ Kit Set Up. Ojectives This presentation is intended to provide a guide on how to use, set up, and restore the new LZ kits.
Snapdragon S1 APQ7027A-based DragonBoard Quick Start Guide Rev. B June 2012 MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION Copyright.
CR30-X Service Training. 2Created by Claus Steiner - 23 September 2006 Safety: Working with the Digitizer (1) Light injuries, damage Serious injuries,
A 5 ANTENNA GROUP OE-254/ GRC AGENDA * PURPOSE * TASKS, CONDITIONS AND STANDARDS * DESCRIPTION * TECHNICAL CHARACTERISTICS * WARNING STATEMENTS * INSTALLATION.
1 Chapter 1: Getting Started Presentation based on: "What's a Microcontroller ?" By Andy Lindsay Parallax, Inc Electronics Technology Core Pickens Tech.
Step-by-Step: Turn on Widow/Orphan Control OPEN the checking document from the data files for this lesson. 1.Scroll to the top of page 2 and notice the.
How a Well is Drilled on Land 1 Step 1: Digging a Cellar On land, a majority of wells begin with digging a cellar from three to fifteen feet in depth.
Questionnaire on Water Consumption in Sweden P1 From what source do you consume water from most frequently ? P2 Is your home connected to the public system.
© 2016 SlidePlayer.com Inc. All rights reserved.