Presentation is loading. Please wait.

Presentation is loading. Please wait.

Diagram Review / Matrix. 2 AUMA Wiring Diagrams New Wiring Diagram Designation SA.2 NORM AC.1 AC.2 Dimensional Diagrams Where to find wiring diagrams.

Similar presentations


Presentation on theme: "Diagram Review / Matrix. 2 AUMA Wiring Diagrams New Wiring Diagram Designation SA.2 NORM AC.1 AC.2 Dimensional Diagrams Where to find wiring diagrams."— Presentation transcript:

1 Diagram Review / Matrix

2 2 AUMA Wiring Diagrams New Wiring Diagram Designation SA.2 NORM AC.1 AC.2 Dimensional Diagrams Where to find wiring diagrams Tagging Information

3 3 New wiring diagram designations

4 4 Current designation…..  KMS – SA.1 NORM actuator  MSP – actuator with AM controls  ACP – actuator with AC.1 controls  SD – actuator dimensional diagram New designation…..  TPA – SA.2 NORM actuator  MSP – actuator with AM controls  TPC – actuator with AC.2 controls  ACP – actuator with AC.1 controls  DDS – actuator dimensional diagram

5 5 TPC – Terminal Plan Controls AC2AMAC1 Multi-turn SA 07.2 – 16.2 TPC TPA MSP TPA ACP TPA SA 25.1 – 48.1 TPC TPA MSP TPA ACP KMS TP SA 07.1 – 16.1 TPC KMS TP MSP KMS TP ACP KMS TP Part-turn SG 05.1 – 12.1 TPC TPA MSP TPA ACP KMS TP

6 6 TPA wiring Similar to KMS Wiring

7 7 SA.2 NORM Diagrams

8 8 Norm SA.2 Wiring ( schematic ) Motor connections External control connections Legend

9 9 Norm SA.2 Wiring ( point to point ) Motor connections External control connections Legend

10 10 TPA Wiring diagram codes KMSTP 100/001TPA00R1AA TPA: 00R1AA  new code  required due to new features  fully compatible to the old system (KMS)

11 11 TPA Code system R1AA Motor 00  AUMA 3ph 01  L. 1ph. 50  with AM/C 16  SG Closing direction: R:= CW; L:= CCW Pos. Trans: 0:= w/o A:= Pot E:=RWG; Q/I:=MWG Signalization: 1:= Blinker, 2:=BL+ Manual Limit Switches: A:= 8; B:= 8.2 Torque Switches: A:= 6; B:= 6.2 Tandem Sw. Motor protection: 1:= 1xTH; 2:= 1xPTC etc… Heater:1:= V &24Vdc 2:= 380V-400V Reserved

12 12 KMS to TPA Comparison table OldNew IFAX Switches KMS60TP or. 15 TPTPA01… KMS61TP or 26 TPTPA02… KMS62TP or 27 TPTPA03… KMSTP100/001TPA00R1AA /8 KMSTP200/001TPA00R2AA /8 KMSTP104/001TPA00R1AA-0E1-0006/8 KMSTP140/001TPA00R1AA-0C1-0006/8 KMSTP180/001TPA00R1AA-0I1-000n/a KMSTP110/001TPA00R1AA /8 KMSTP210/001TPA00R2AA /8 KMSTP110/201TPA00R1AB /8.2 KMSTP110/211TPA00R1AF /9 KMSTP110/101TPA00R1AB /8 KMSTP110/011TPA00R1AE /9 KMSTP110/301TPA00R1BB /8.2

13 13 Actuator Wiring AC.1

14 14 Typical ACP / TPA (AC.1 on SA.2) Drawing

15 15 Actuator Wiring AC.2

16 16 TPC numbering system DigitMeaning 1Type of controls 2Interface to DCS 3Analog inputs 4Digital inputs 5Remote indication: status contacts, position/torque feedback 0/4 – 20 mA 6Additional equipment 7Local controls 8Supply voltage: external supply 24 V DC/auxiliary voltage for controls/supply voltage tolerance 9Switchgear 10Motor protection options 11Heater 12-14Specials

17 17 TPC numbering system TPC - Terminal Plan Controls

18 18 Typical TPA / TPC Wiring Diagram

19 19 TPC – Terminal Plan Controls AC2AMAC1 Multi-turn SA 07.2 – 16.2 TPC TPA MSP TPA ACP TPA SA 25.1 – 48.1 TPC TPA MSP TPA ACP KMS TP SA 07.1 – 16.1 TPC KMS TP MSP KMS TP ACP KMS TP Part-turn SG 05.1 – 12.1 TPC TPA MSP TPA ACP KMS TP

20 20 MSP

21 21 Typical MSP / KMS Wiring Diagram

22 22 MSP – Customer connections Supply power Demand signal E 1 Feedback signal (position) Selector switch status Fault relay status Control power Remote command (mode) Auxiliary limit contacts

23 23 MSP – Control section Refer to Drawing LEGEND for internal circuit board descriptions Circuit board labels are present on drawing

24 24 MSP - Actuator terminals Motor wiresMotor Control circuit w thermal protection Feedback signal (position) Auxiliary limit contacts PotentiometerHeater

25 25 New Dimensional Diagram Code System

26 26 DDS Code system D211AAAAA011 Output Drive Gearbox Models / Valve Flange Handwheels and Input Shaft Sizes Motor Types Actuator Models Gearbox Versions / Mounting Positions. Integral Control Version Customer Electrical Connection Mounting Position for Controls Housing and Covers

27 27 Typical DDS Dimensional Diagram

28 28 Diagram Availability How can you access the diagrams?

29 29 Customer Order Diagrams  Drawing Submittal to the Customer Wiring Schematic Diagram  Actuator Customer Cover Wiring Schematic Diagram  Drawing vault Wiring Schematic Diagram Detailed Wiring Diagram

30 30 Internet

31 31 Go To :  Support  Sample wiring diagrams The table is based on description:

32 32 Go To : Customer Service  Sales reps site Log in using Username and Password  Drawing Vault

33 33 Updated Tagging Information Additional information available at: Pre November 2011 November 2011 and later

34 34 Questions ???


Download ppt "Diagram Review / Matrix. 2 AUMA Wiring Diagrams New Wiring Diagram Designation SA.2 NORM AC.1 AC.2 Dimensional Diagrams Where to find wiring diagrams."

Similar presentations


Ads by Google