1. FANCOILS CONTROLS ELECTRONIC BOARD - KCMS CMS - KCMS/PCM CMSPCM NEW WIRED CONTROL PANEL - KPCM

2. FUNCTIONS

3. CONTROLLI NEW CONTROLLI IDROWALL FREND YARDYEV BRIOEV UTNC-EV UTNB
KICM
KTCM
KPCM
YARDYEV
NEW
IDROWALL FREND BRIOEV UTNC-EV
BRIOEV
UTNC-EV
UTNB
UTNA

4. CONTROLS CMS KCMS CMSPCM KCMS/PCM KICM KPCM KTCM RI-KRI STI KSTI
MVR KMVR

5. CONTROLS New codes for electrical board and panel CMSPCM KCMS/PCM
CMS KCMS
KPCM

6. New electronic board KCMS CMS
OLD
mario
SCR ECO digital input don’t change, SIC EIR change their position
New digital input DI5 (not available for Frend and Idrowall) for new function:
OCCUPANCY function (NC) only for KICM panel, (by modifying board parameters (P45=8;P93=3) trough installer password on the KPCM control panel)

7. New electronic board KCMS CMS
OLD
OLD
NEW
New digital output CCH CCA

8. FUNCTIONS
SETTING FUNCTIONS
COMFORT FUNCTIONS

9. FUNCTIONS SETTING FUNCTIONS Full auto Cool Dry KICM Fan KPCM Heat KTCM
Heat + heater
Full Auto + heater
NOVELTY
Full AUTO: the desired temperature is showed on the display. The unit, according to the room temperature and the setting temperature, sets the working mode (cool/heat).
User set temperature
Legend
mode
room temperature
HEAT
OFF
COOL
P02=2°C
P03=2°C
P04=0,5°C

10. FUNCTIONS ATTENTION COMFORT FUNCTIONS KICM KPCM KTCM
Orienting/swing (on Idrowall)
Clock
Timer
Sleep
Hot start
Too cool
Memory
Economy (ECO)
Lock function / Blocco remoto (KICM)
ON/OFF remote control (SCR)
Summer/Winter remote control (EIR)
Security control (SIC)
Occupancy (only KICM) new
Probe IN/OUT
Continuous ventilation
Alarm
MASTER/SLAVE
Periodic ventilation
Confort control new
Blocco tastiera (solo KTCM)
KICM
KPCM
KTCM
ATTENTION
The following functions aren’t available with KICM control panel:
Orienting/swing - Clock - Timer - Continuous ventilation (by key) – Keybord stop
Probe IN/OUT function is available for:
KICM trough DIP SWITCH (DIP6) setting
KPCM trough key on the panel
Not used with the remote control KTCM (the probe is always set in the unit)
The periodic ventilation is always disabled with KPCM and KICM with Probe In function activated (probe into the unit)
Confort control (by modifying board parameters P36=1 trough installer password on the KPCM control panel).

11. COMFORT CONTROL FUNCTION
Comfort control (by parameters)
When the set-point is decided by a system manager (supervision), the Comfort Control function gives the possibility to increase or reduce the Set-point (+-3°C) in the room with the UP-DOWN bottoms.
(The function have to be enable modifying board parameters P36=1 trough installer password on the KPCM control panel.)
The set value is 22 °C
User set temperature
22°C
Legend
mode
room temperature
HEAT
OFF
COOL
P02=2°C
P03=2°C
P04=0,5°C

12. LOCK FUNCTION FUNCTION
Attention: to obtain the changing set-point ±3°C must be set the Confort Control Function

13. DIP-SWITCHES
Changes to the DIP-Switches must be made with the board disconnected from the power supply.
The DIP-Switches on the electronic board (see right figure) can be changed using a sharp tool. The DIP-Switches can be changed correctly by following the instructions present on the component and in the following table.
OLD
NEW

14. DIGITAL INPUT/FUNCTION: OCCUPANCY (NOT FOR IDROWALL FREND* )
ONLY x KICM
In case of supervising system (BMS) with OCCUPANCY function it is possible to activate 3 different working modes (by modifying board parameters P45=8; P93=3 trough installer password (60) on the panel):
Not booked room = OFF
Occupied room = Comfort mode
Booked and not occupied room = Stand-by/Economy mode
Not occupied OFF
Occupied Comfort mode
There is a person in the room. The fancoil works with desired temperature value for fixed time (15 min).
Set-point = desired temperature value
The occupancy status can be activated:
By one of the keys in the panel (not ON/OFF) for a set period of time (parameter P94=15 min). At the end of the time periods (15 min) the occupancy status can be enabled again
With movement sensor on DI5 digital input
Pressing Sleep key for 5 sec the Occupancy function continues up to unit switch-off
Booked and not occupied Stand-by/Economy mode
There is no person in the room. The fancoil works with economy set-point for energy savings
Set-point = economy
* Only with ECO (DI4, parameter P44=8)
NOTA BENE Con funzione Occupancy abilitata non utilizzare l’ingresso igitale ECONOMY

15. DIGITAL OUTPUT: FUNCTION
CCH
Chiller input, chilled water required from the thermostat (NO)
CCH –Chiller input

16. DIGITAL OUTPUT: FUNCTION
CCA
Boiler input, hot water required from the thermostat (NO)
CCA – Boiler input