Presentation is loading. Please wait.

Presentation is loading. Please wait.

The MGV 130 system The system for mounting dental models into articulator without use of any plaster! (Minimal working height of articulator - 116mm)

Similar presentations


Presentation on theme: "The MGV 130 system The system for mounting dental models into articulator without use of any plaster! (Minimal working height of articulator - 116mm)"— Presentation transcript:

1 The MGV 130 system The system for mounting dental models into articulator without use of any plaster! (Minimal working height of articulator - 116mm)

2 The MGV 130 system - upper part The setting options:,F - Fixed prosthetics,S - Sensing prosthetics Standard setting – position,F The MGV 130 system - lower part Key MGV 130 Tightening key Plastering form Rubber formerMetal plates Inserting plates – Modellsystem 2000* Inserting plates – Giroform* Inserting plates – Accu-Trac* *Giroform is registered trademark of Amann Girrbach GmbH, Pforzheim, DE, *Accu-Trac is registered trademark of Coltene/Whaledent AG, 9450 Altstätten, CH, *Modellsystem 2000 is registered trademark of Baumann Dental GmbH, Keltern-Ellmendingen, DE Single parts of MGV 130 system

3 Prepare a casting plate and insert little metal pad Pour plaster over and make a casting Sand the modelPrepare the articulator – the joint track is lockedThe upper portion of MGV 130 is mounted The lower portion of MGV 130 is mounted Both upper and lower parts of MGV 130 are mounted in the articulator Set +1mm on the incisial rod Operating procedure with MGV 130 system The recommended height of the model is 30mm including the technology used

4 Insert a suitable adapter to work with a trayMount the bottom panel Align the bottom model with the incisor point and the occlusal plane (using a rubber band). Incisor centre and interbuccal bump of tooth no. 6 Tighten the lower part of MGV 130Insert the model of the upper part Use a suitable bite registration materialAttach the upper model to fit the bite Loosen lateral locking screw on the upper part of MGV 130 Loosen upper locking screw on the upper part of MGV 130

5 Remove the bite registration material, return the incisial rod to the 0 position and check maximum contact using articulation paper Remove both models and the transition plate All screws must be tighten gradually, first gently and then using greater force Insert the MGV 130 key. Blue with blue, red with red Adjust and tighten the MGV 130 key. Its best to tighten both screws simultaneously The removed MGV 130 key has been adjusted to specific work After repositioning the tooth models back to the MGV 130 system, the articulator is ready for further work First tighten the upper screwThen tighten the side screw

6 Operating procedure for change upper part of MGV 130 system from,F position to,S position Prepare the upper part of MGV 130Unscrew the lateral screw and take out the pad Displace the axis from the right side and slide the segment out of the arms Loosen the upper screw and turn the segment into the S position Insert the segment in between the arms, then insert the axis from the right side, fix the pad from the left side and screw in the lateral screw Fasten the upper part of MGV 130 to the upper arm of the articulator

7 Options for use of various split cast techniques Plaster + Accu-Trac* Options for use of various split cast techniques Pins + Plaster Options for use of various split cast techniques Giroform* + Modellsystem 2000* Options for use of various split cast techniques Pins + Modellsystem 2000* *Giroform is registered trademark of Amann Girrbach GmbH, Pforzheim, DE, *Accu-Trac is registered trademark of Coltene/Whaledent AG, 9450 Altstätten, CH, *Modellsystem 2000 is registered trademark of Baumann Dental GmbH, Keltern-Ellmendingen, DE Examples of use MGV 130 system

8 Contains: MGV 130 system – Upper and Lower part MGV 130 Key Tightening key – 2x Inserting plates for Modellsystem 2000* - 2x Inserting plates for Giroform* - 2x MGV 130 plastering form – 2x Rubber former – 2x Metal plates – 6x MGV 130 system – complete setMGV 130 system – basic set Contains: MGV 130 system – Upper and Lower part Tightening key – 2x Plastering form set Contains: MGV 130 plastering form Rubber former Metal plates – 6x *Giroform is registered trademark of Amann Girrbach GmbH, Pforzheim, DE, *Accu-Trac is registered trademark of Coltene/Whaledent AG, 9450 Altstätten, CH, *Modellsystem 2000 is registered trademark of Baumann Dental GmbH, Keltern-Ellmendingen, DE The MGV 130 system - Sets

9 Cleaner work Faster work Saving of working time Big saving of plaster Patent pending – WO 2013/ The MGV 130 system


Download ppt "The MGV 130 system The system for mounting dental models into articulator without use of any plaster! (Minimal working height of articulator - 116mm)"

Similar presentations


Ads by Google