Presentation is loading. Please wait.

Presentation is loading. Please wait.

1/25 Title : Director Name : Simon Hsu Organization : Vehicle Safety Certification Center Economy : Chinese Taipei APEC TPT-WG 39, New Zealand, Apr. 2014.

Similar presentations


Presentation on theme: "1/25 Title : Director Name : Simon Hsu Organization : Vehicle Safety Certification Center Economy : Chinese Taipei APEC TPT-WG 39, New Zealand, Apr. 2014."— Presentation transcript:

1 1/25 Title : Director Name : Simon Hsu Organization : Vehicle Safety Certification Center Economy : Chinese Taipei APEC TPT-WG 39, New Zealand, Apr Chinese Taipei s Progress Report on Regulation Harmonization

2 2/25 Amendment/Revision based on UN Regulations New Technical Regulations Using UN as a basis Considerations on Specific Safety Issues CONTENTS

3 3/25 Periodical Review : Twice a year (1 st half & 2 nd half), 1 st half of /10/12, 2012/11/07, 2012/11/29 and 2013/03/08 (published by MOTC on 2013/11/01) 2 nd half of /6/26, 2013/7/24, 2013/7/31 and 2013/8/27 (published by MOTC on 2014/01/03) 1 st half of /2/13, 2014/2/21, 2014/3/11 and others meeting undecided. 2 nd half of compilation was prepared to be discussed in 2 nd half of 2014 Review on corresponding UNs amendment/revision for existing regulation; the Transitional Provision is taken into consideration, as appropriate, to allow necessary lead time Amendment/Revision on Existing Regulations

4 4/25 Technical RegulationUN VersionSummary 020.Specification for Motor Vehicle UN R Amending requirements for escape hatches and gangway mannequin of articulated buses. 033/034. Installation of Lights UN R48 04-S7 UN R53 01-S13 Amending requirements for electrical connections of main-beam and AFS TyreUN R75 00-R2/C1 Amending the content of Table, such as Section width mm revised into Maximum overall width mm. 322 Front Fog lamp UN R19 04-S1 Adding requirements for objective luminous flux Front position lamps UN R07 02-S19 UN R50 00-S15 Amending intensity of light emitted and colour of light emitted Rear position lamps UN R07 02-S19 Amending requirements for intensity of light emitted Stop lampsUN R07 02-S19 Amending requirements for intensity of light emitted S3 stop lampsUN R07 02-S19Amending requirements for intensity of light emitted End-outline marker lampsUN R07 02-S19 Amending requirements for intensity of light emitted. Discussed in 1 st half of 2012 (1/2

5 5/25 Discussed in 1 st half of 2012 (2/2 Technical RegulationUN VersionSummary 422. Dynamic Braking UN R13 11-S7 Amending requirements for brake failure and defect warning signal and braking test, performance of braking systems ABSUN R13 11-S7 Amending requirements for failure within the electric control transmission Prevention of fire risks for the large passenger vehicle UN R Adding requirements for alarm system to detect a temperature in the engine compartment and in each compartment where a combustion heater is located EMCUN R10 04-C1 Adding requirements for related definitions, testing for conducted disturbances on AC or DC power lines, testing for immunity of vehicles to surges conducted along AC and DC power lines and testing for conducted disturbances on Network and telecommunication access from vehicle AFSUN R S1 Amending requirements for general specifications, illumination, stability of photometric performance of systems Construction of Low- Floor Bus UN R Adding requirements for the vertical distance between the floor of the seating area and the adjacent gangway shall be not more than 250 mm.

6 6/25 Technical Regulation UN Version Summary 202. Retro-reflective markingsUN R S7 Amending the Table of Minimum values for the Coefficient o Retro-reflection R. 034 Installation of LightsUN R48 05-S1 Amending requirements for tell-tale of front position lamp and rear position lamp Safety glassesUN R43 01 Amending requirements for related definitions, points of impact, mechanical strength test, headform test and test of resistance to high temperature and so on Filament lamps UN R37 03-R6/C1 UN R99 00-S7 Adding filament light source filament lamp of definition. Amending requirements for starting, run-up and hot-restrike characteristics and electrical and photometric characteristics Gas-discharge Headlamps UN R98 01-S2 UN R S10 Amending requirements for test voltage related gas discharge light source with ballast integrated with the light source Front position lampsUN R07 02-S17 Amending requirements for interdependent lamp system. Discussed in 2 nd half of 2012 (1/2

7 7/25 7 Technical Regulation UN Version Summary 370. Stop lampsUN R07 02-S17 Amending requirements for interdependent lamp system End-outline marker lampsUN R07 02-S17 Amending requirements for interdependent lamp system The protection of the occupants in the event of a lateral collision UN R95 03-S1Amending definition of exposed conductive part The protection of the occupants in the event of a frontal collision UN R94 02-S2Amending definition of exposed conductive part Headlamp (HID excluded)UN R S10 Amending requirements for test voltage related gas discharge light source with ballast integrated with the light source AFSUN R S2 Amending Table: Passing beam photometric requirements. 640.Electric safety requirements for battery electric vehicles UN R S1Amending definition of exposed conductive part. Discussed in 2 nd half of 2012 (2/2

8 8/25 8 Technical Regulation UN Version Summary 020.Specification for Motor Vehicle UN R S1 Amending requirements for exits and interior arrangements of articulated buses. 033/034/035. Installation of Lights UNR48 05-S2, 06 UN R53 01-S13 UN R73 01-S7 Adding requirements for related definitions, relative general provisions. Amending requirements for headlamps of class A for L category and exterior courtesy lamps Flammability of the interior materials UN R Harmonize with UN R118, adding requirements for definitions, burning behaviour of the components, test to determine the horizontal/vertical burning rate of materials Installation of devices for indirect vision UN R46 03 Amending requirements for definitions, rear view mirrors required for L-category vehicles with body work, exterior rear-view mirror on the driver's side. Adding requirements for calculation of the detection distance Safety beltUN R16 06-S2Amending requirements definitions for seats. Discussed in 1 st half of 2013 (1/4

9 9/25 9 Technical Regulation UN Version Summary 270. Devices for indirect visionUN R46 03-S1 Amending requirements for definitions, general specifications, dimension, Impact test. Adding requirements for determination of the displayed object size Tyre UN R30 02-S17 Amending requirements for definitions, Load/speed performance test. 302 Gas-discharge HeadlampsUN R98 01-R3/C1 Amending requirements provisions concerning passing beams, tests for stability of photometric performance of headlamps in operation. 322 Front Fog lamp UN R19 04-S3 Amending requirements for general specifications for class F3, Illumination, other photometric requirements and tests for stability of photometric performance Front position lampsUN R07 02-S20 Amending requirements for relative interdependent lamp system Rear lampsUN R07 02-S20 Amending requirements for relative interdependent lamp system. Discussed in 1 st half of 2013 (2/4

10 10/25 10 Technical Regulation UN Version Summary 360. Parking lampsUN R77 00-S14 Amending requirements for colour of light emitted. Adding requirements for relative test procedure Stop lampsUN R07 02-S20 Amending requirements for relative interdependent lamp system End-outline marker lamps UN R07 02-S20 Amending requirements for relative interdependent lamp system. 422/423. Dynamic Braking UN R13 11-S9 UN R13H 00-S14 Amending requirements for special additional requirements for service braking systems with electric control transmission, braking tests and performance of braking systems, secondary braking system, special requirements for vehicles equipped with a VSF. Adding requirements for braking tests and performance of braking systems Steering control system UN R12 04-S1 Amending requirements for "Exposed conductive part of definition Headlamps (headlamps of gas-discharge type excluded) UN R UN R S1 UN R S2 Amending requirements for related definition, stability of photometric performance, lamps incorporating lenses of plastic material and Illumination. Discussed in 1 st half of 2013 (3/4

11 11/25 11 Technical Regulation UN Version Summary 481/482. Safety belt anchorageUN R14 07-S3 Amending requirements for definitions, location of belt anchorages. Adding requirements for particular test requirements for seat belt anchorages. 490/491. Seats UN R17 08-S1 UN R80 03 Amending requirements for definitions, installation of seats in a vehicle type, dynamic tests. Adding requirements for the installation of side- facing seats, safeguarding of passengers in side- facing seats Headlamp (HID excluded)UN R S2 Amending requirements for replaceable LED module AFSUN R S3 Amending requirements for tests for stability of photometric performance of systems and table of passing beam photometric requirements Low floor vehicle UN R S1 Amending requirements for the width of priority seats. Discussed in 1 st half of 2013 (4/4

12 12/25 12 Drafted in 2012, 2013 and /2 UNTitle of Item Scope and proposed date of implementation Status Large vehicleSmall vehicleMotorcycle 14ISOFIX /1/1---Announced by MOTC on 2014/01/03 23 Manoeuvring lamps 2014/1/1 ---Announced by MOTC on 2013/05/09 34Fuel Tank2014/1/ Announced by MOTC on 2012/9/26. 2.Metallic and plastic fuel tank shall comply with hydraulic test and overturn test, for M and N. 58 Rear underrun Protection To be determined --- Under discussion 64 Tyre pressure monitoring system (TPMS) /11/1---Announced by MOTC on 2012/11/5. New Technical Regulations Using UN as a basis

13 13/25 13 UNTitle of Item Scope and proposed date of implementation Status Large vehicleSmall vehicleMotorcycle 107 Specification of open-top single- decker and double-decker buses To be determined --- Expecting to be announced by MOTC 129 Automatic Emergency Braking Systems (AEBS) To be determined--- Under discussion RE3 Acoustic vehicle alerting system 2015/1/1 2016/1/1Announced by MOTC on 2013/11/01 Drafted in 2012, 2013 and /2 New Technical Regulations Using UN as a basis

14 14/25 Implementation UN for M2/M3/N2/N3/O3/O4 UN for M1/N1/O1/O2 UN for L1/L2/L3/L5 Total 2004R36, R3, 6, 7, 16, 19, 23, 28, 30, 37, 43, 48, 54, 77, 91, 98, 99, R3, 6, 7, 16, 19, 23, 28, 30, 37, 39, 43, 54, 77, 91, 98, 99, R39, 53, 60, 74, 81, 98, R19, 28, R5, 13, 14, 17, 25, 31, 38, 39, 66, 79, 80, 112, R5, 11, 12, 13, 13h, 14, 17, 25, 31, 38, 48, 79, 94, 95, 112, R3, 37, 50, 112, 113, R R46, 123, 55 3 R46, 10, 1233R R R10, 100, 343R100, 34, 6433 Announced Summary of UNs Introduction (1/2)

15 15/25 Announced Reg. by MOTC but not yet effective: 1 (UN R64 ) Postponed Reg. by MOTC: 18 Announced & effective Reg. by MOTC: 51 Summary of UNs Introduction (2/2)

16 16/25 Considerations on Specific Safety Issues Active Safety for Bus Collision Evasion – AEBS Cared-for Transportation – Wheelchair Accessible Vehicle Blind Spot clearance – Maneuvering Lamp Pedestrian Safety – AVAS ISOFIX Rear underrun Protection ESC/VSF 3-point seat-belt for large passenger vehicle

17 17/25 67 meters Ahead Automatic Emergency Braking Systems Scope: This Regulation applies to motor vehicles of categories M2, M3, N2 and N3. Objective: To automatically avoid the collision or at least to mitigate its effects. 3.8S > Based on time to collision (TTC) Phase-I warning operates (visual) Phase-II warning operates (audible) Phase-III Emergency braking operates stationary target Moving bus at 80 km/h 0S 3S 98 meters Ahead4.4S

18 18/25 Scope: This Regulation applies to wheelchair accessible vehicles of categories M1~M3 (except for Low floor vehicle). Objective: To enhance the vehicle safety and accessibility for disabled passengers to get on, get off and ride in wheelchair. Wheelchair accessible vehicle

19 19/25 Scope: This Regulation applies to manoeuvring lamps for vehicles of categories M and N. Objective: To provide supplementary illumination to the side of the vehicle to assist during slow manoeuvres. 19 Zones of observation Boundaries of the zones Manoeuvering lamps

20 20/25 Scope: This Regulation applies to electric vehicles for L, M and N. Objective: Sounds designed to alert pedestrians to the presence of electric drive vehicles such as hybrid electric vehicles (HEVs), plug-in hybrid electric vehicles (PHEVs), and all-electric vehicles (EVs) travelling at low speeds. Acoustic Vehicle Alarming System

21 21/25 Scope: This Regulation applies to ISOFIX for vehicles of categories M1. Objective: To define standard attachment points to be manufactured into cars, enabling compliant child safety seats to be quickly and safely secured. ISOFIX

22 22/25 Scope: This Regulation applies to rear underrun protection for vehicles of categories O2, O3, O4, N2 and N3. Objective: To prevents the vehicles from being wedged under the chassis during accidental crashes and with that significantly increases the safety of traffic participants Rear Underrun Protection A.is a Minimum of 100 millimetres; B.is the maximum distance from the ground (when unladen) being 550 millimetres

23 23/25 Scope: This Regulation applies to ESC/VSF for vehicles of categories M1, M2,M3, N1, N2, N3, O3 and O4. Objective: ESC/VSF is a safety feature that detects and prevents (or recovers from) skids. It can help keep the driver from losing control of the car in a panic swerve or when driving on slippery roads. ESC/VSF

24 24/25 Scope: This Regulation applies to the rear middle seat which faces aisle, in categories M2 (gross vehicle weight > 3.5 t) and M3. Objective: To prevent the passenger who sits in the rear middle seat which faces aisle from dangerous fallout when vehicle suddenly stops. 3-point seat-belt for large passenger vehicle As of Jan. 01, 2019, the rear middle seat which faces aisle, in categories M2 (gross vehicle weight > 3.5 t) and M3, shall have a at least 3- point safety-belt

25 25/25 Thank you for Your Attention !! Sharing and Cooperation!!


Download ppt "1/25 Title : Director Name : Simon Hsu Organization : Vehicle Safety Certification Center Economy : Chinese Taipei APEC TPT-WG 39, New Zealand, Apr. 2014."

Similar presentations


Ads by Google