Presentation on theme: "Canon 6000 series When taking cartridge out of the printer, make sure to seal the ink outlet with Scotch tape before refilling the ink. Step 1 Step 2 Make."— Presentation transcript:
Canon 6000 series When taking cartridge out of the printer, make sure to seal the ink outlet with Scotch tape before refilling the ink. Step 1 Step 2 Make a needle hole on top upper right-hand corner of the ink resevoir. Dont make hole too big.
Canon 600 series Refill ink slowly. Do not fill the ink to exceed the level of the hole you just made. After fully reflling the resevoir, clean the surface with a dry paper towel and seal the refilling hole with Scotch tape. Step 3 Step 4
Canon 600 series After refilling the ink and sealing the refilling hole, the cartridge looks like this. Remove the tape from the original ink outlet before inserting the refilled cartridge into the printer. Wipe the ink outlet with a paper towel for any leaks. Step 5 Step 6
Canon 4000 series On the bottom of the cartridge you will see ink refilling hole/s. Do not pierce the needle into the refilling hole/s. Hold the needle point just above the refilling hole/s and release the ink drop by drop into the refilling hole/s. The refilling hole/s has a filter which will absorb the refilling ink. Color Cartridge Black cartridge Same procedure as Step 1
Epson cartridge Take the cartridge out of the printer,and clean the residual ink with a dry paper towel and seal the original ink outlet with the Scotch tape to prevent any leaking when refilling the cartridge. Step 1 Step 2 Tear off the top hot-sealed original film from the cartridge. You will notice a color chamber refilling hole for each color. Be careful NOT to refill ink into the wrong color chamber. For grey-colored cartridges you can check ink color with a cotton bud or tooth pick.
Pierce the needle into the rear refilling hole of the color chamber. Refill the ink SLOWLY to prevent any formation of air bubbles. After refilling the ink, only seal the refiling holes of the color chambers with Scotch tape. DO NOT SEAL THE ENTIRE TOP COVER. Tap the refilled cartridge few times to remove any trapped air inside the cartridge. Leave this area open Step 3 Step 4
Step 5 Remove the tape from the original ink outlet. Please use a dry paper towel to wipe any leakage from the outlet and before inserting the cartridge into the printer. It is suggested not to use this refilled cartridge immediately after refilling Ink outlet
Remove te top rubber ball bearing from the hole in the cap by using a thumb tack. Hewlett Packard 51626A(black) Step 1 Pierce the refilling needle into this hole. Do not insert the needle too deep to avoid punctuating the air bag inside. Place a dry paper towel under the original ink outlet when refilling ink to absorb any leakage. Step 2
Use a syringe with a special rubber attachment and place it into the Aperture C located in the bottom of the cartridge as shown in the above picture, to suck out any air bubbles in the cartridge. If the air is not sucked out completely the cartridge might leak. Step 3 Aperture C Printhead IMPORTANT PROCESS
Place the ball bearing into its original position in the plastic cap. Step 4 Check the ink outlet with a dry paper towel to ensure the ink is flowing. In case of continuous leakage, repeat Step 3 to remove any remaining air bubbles. Step 5
Hewlett Packard 51625A(color) The filler holes of the cartridge are loacated under the top plastic cover cap. Use a thin phillips screwdriver to prise open the cover. Filling the ink into the center correct color hole of each ink chamber. Be careful NOT to refill the ink into the wrong color chamber. Step 1 Step 2
After refilling check the original ink outlet with a dry paper towel to ensure that ink is flowing. Replace the prised top plastic cover into its original position and seal firmly with the Scotch tape. Step 3 Step 4
Lexmark Pierce the needle into the top small hole of the cartridge. Do not over fill with ink as it might leak. Using a dry paper towel to check if the ink flowing from the original ink outlet before inserting the cartridge into the printer. Step 1 Step 2