Presentation is loading. Please wait.

Presentation is loading. Please wait.

Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue.

Similar presentations


Presentation on theme: "Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue."— Presentation transcript:

1 Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue gun Production cost worksheet Directions: 1.Listen to the manager read the task sheet. 2.Review the steps on the picture walk before you begin. 3.Following the picture walk, complete the steps to make a snowflake coaster. 4.When you are done, clean up your area. Wash the sponge brush thoroughly so that it can be reused. 5.Put your coasters in a safe place to dry. 6.Complete the production cost worksheet. 7.Put your finished worksheet in the completed rotation basket when you are done. PBL Connection: Becoming an Entrepreneur I can add, subtract, multiply and divide decimal numbers. Standard 5.NBT.7 I can make precise measurements and specify the units. Standard SC 5.5.1

2 Snowflake Coasters Name _____________________ Directions: Complete the calculations to determine the production cost per coaster. Show all work. Expenses: Fabric5.99 Sanders5.94 Spray Paint x 4 Tiles8.00 High Gloss Coating5.99 Modge Podge4.99 Total snowflake coasters produced = 50 Per product cost = ________ Suggested retail price for a set of 4 coasters = _______ I can add, subtract, multiply and divide decimal numbers. Standard 5.NBT.7

3 Step 1: Sand all the rough edges off of the tile with the sander. Step 2: Wipe off all the dust with the damp cloth. TIP: Make sure your work space is free of dust after you are done sanding your tile.

4 Step 3: Measure the width at 4 ¼ inches. Measure the height at 4 ¼ inches. TIP: Remember to work from the edge of the fabric to conserve your materials. Step 4: Draw a line marking the edges of the square you measured.

5 Step 5: Use your scissors to cut out your square. Step 6: Use hot glue to put glue down around the edges of the tile and a large x in the middle of the tile. Place the felt onto the tile and smooth it out so that it lies flat. TIP: Be careful not to burn yourself! You can use a ruler to smooth out the felt onto the tile if you dont want to touch the felt with your hands.

6 Step 7: Gather your materials to place the snowflake onto your coaster. Step 8: Use the sponge brush to brush a fine layer of Modge Podge onto the top of the tile. TIP: Place a piece of foil under your tile to create a workspace. You will keep your coaster on the foil until it dries and the final step is completed.

7 Step 9: Center the snowflake on the tile. TIP: Make sure that everyone places their snowflake on their tile in the same position as yours. These four tiles will make one coaster set! Step 10: Brush a heavy layer of Modge Podge onto the top of the tile and the snowflake. Cover this space thoroughly! Be careful not to move your snowflake as you brush it.

8 Step 11: Your completed tile should look similar to the one pictured below. Last step: Your finished product will look like this when it dries! TIP: Keep your tile on the foil somewhere safe in your classroom until it is completely dry. Mrs. Spear will spray all the tiles with a water resistant sealant before you assemble the coasters for sale.


Download ppt "Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue."

Similar presentations


Ads by Google