Presentation is loading. Please wait.

Presentation is loading. Please wait.

FM Electronics Product Information & Product Finder I Know the Part Number I Know the Part Number I need POLICE response I need POLICE response 4000 series.

Similar presentations


Presentation on theme: "FM Electronics Product Information & Product Finder I Know the Part Number I Know the Part Number I need POLICE response I need POLICE response 4000 series."— Presentation transcript:

1 FM Electronics Product Information & Product Finder I Know the Part Number I Know the Part Number I need POLICE response I need POLICE response 4000 series Class 3 4000 series Class 3 4000 series Class 6 4000 series Class 6 8000 series External 8000 series External Audible only (Bells only) Audible only (Bells only) EXIT TO WINDOWS EXIT TO WINDOWS TIP: You can press the Esc key to exit this programme at any time Find Part by Description Find Part by Description Link to website Link to website

2 For Police response the system MUST be: 1: Installed by an Inspectorate recognised company. 2: Be monitored by an Alarm Receiving Centre (ARC). 3: Be maintained by an Inspectorate recognised installer. (Alarm Inspectorate usually = NACOSS or SSAIB) Are you Inspectorate recognised? Not Inspectorate Recognised Inspectorate Recognised

3 You need an inspectorate recognised company for this installation, If You heard about our product from an alarm installer you will need your installer to supply and fit the system, we supply trade only. If From another source, (Internet etc..) Look in your telephone directory for NACOSS or SSAIB recognised installers who can assist you or contact FM Electronics who will give you contact details for your nearest installer(s). Return to Main Menu

4 You require the FM4000 series product How many zones do you require? Up to 8 zones (circuits) Up to 8 zones (circuits) Up to 64 zones (circuits) Up to 64 zones (circuits) More than 64 zones (circuits) More than 64 zones (circuits)

5 We do not have a single panel with more than 64 zones, please contact your installation company or Technical Support at FM Electronics on 01594 827070 for further assistance. Return to main menu Back to panel menu

6 FM4000 8 Zone Control Panel + Fire & Panic zones plus up to 8 set/unset devices (keypads or remote controls in any combination) Dimensions 270mm wide x 155mm tall x 80mm deep approx. Requires a 12V 2.1Ah battery. Our part no. BAT1. Connections required = mains supply, external sounder & communications device (digi, stu etc.) Absolute maximum working range from furthest device to the control panel 100 metres (this is measured in free space.) The actual maximum working range achieved will vary from site to site and signal strength should be checked before installation is commenced. Devices for this panelExit to Main Menu Checking signal strength

7 4600-GB Infra-red detector 4600-GB Infra-red detector 4650-GB Contact Transmitter 4650-GB Contact Transmitter 4655 Inertia transmitter 4655 Inertia transmitter 4660-GB Smoke Detector 4660-GB Smoke Detector Detection Devices Set/Unset Devices 4173-GB Remote control 4173-GB Remote control 4180 Radio Keypad 4180 Radio Keypad Exit to main menuBack to FM4000 menuAccessories 4005 Tamper Module 4005 Tamper Module 4007 Remote Antenna 4007 Remote Antenna

8 Signal strength can be measured using the control panel, a transmitting device (pir, contact, remote control etc.. (the remote is the easiest) a 12V battery for the control panel and a volt meter. To test the strength, position the panel in its proposed location,power up the control panel (just the 12v battery is sufficient) connect a voltmeter with the DC range selected across the two terminals inside the control panel labelled DVM and press the reset switch, just to the right of the connections terminals. The meter should now read 0V. Go to the required location for the furthest device and send a learn signal from the transmitter (or a PA from a remote control.) The panel will now latch the received signal strength from the device at the panel. (Contact Technical Support at FM Electronics on 01594 827070 if further details are required.) Return to Panel MenuReturn to Main Menu

9 FM4000X & FM4001(used together) 64 Zone Control Panel + 8 Fire & 8 Panic zones plus up to 8 set/unset devices (keypads or remote controls in any combination) Dimensions 270mm wide x 320mm tall x 80mm deep approx. Requires a 12V 2.1Ah battery. Our part no. BAT1 Connections required = mains supply, external sounder & communications device (digi, stu etc.) Absolute maximum working range from furthest device to the control panel 100 metres (this is measured in free space.) The actual maximum working range achieved will vary from site to site and signal strength should be checked before installation is commenced. Devices for this panelExit to Main Menu Checking signal strength

10 4600-GB Infra-red detector 4600-GB Infra-red detector 4650-GB Contact transmitter 4650-GB Contact transmitter 4655 Inertia transmitter 4655 Inertia transmitter 4660-GB Smoke detector 4660-GB Smoke detector 4173-GB Remote control 4173-GB Remote control 4180 Radio keypad 4180 Radio keypad 4160-GB Smoke detector 4160-GB Smoke detector 4155 Inertia transmitter 4155 Inertia transmitter 4150-GB Contact transmitter 4150-GB Contact transmitter 4005 Tamper module 4005 Tamper module FM4000 8 Zone control panel FM4000 8 Zone control panel FM4000X & FM4001, 64 control panel FM4000X & FM4001, 64 control panel FM4000E 8 Zone control panel FM4000E 8 Zone control panel 4100-GB Infra-red detector 4100-GB Infra-red detector 4007 Remote antenna 4007 Remote antenna None of the these? None of the these?

11 10GP General purpose TX 10GP General purpose TX PEN-173 Pendant PA transmitter PEN-173 Pendant PA transmitter 125-HP High power PIR 125-HP High power PIR 115H-HPWP Horizontal curtain PIR 115H-HPWP Horizontal curtain PIR TR4-HP Remote control TR4-HP Remote control TSD-HP Smoke detector TSD-HP Smoke detector DK3-HP Radio keypad DK3-HP Radio keypad TPHP 10mW PA transmitter TPHP 10mW PA transmitter RP2 Repeater station RP2 Repeater station 8008 8 Zone receiver 8008 8 Zone receiver FM8016 Indicator panel FM8016 Indicator panel R1 Single Zone receiver R1 Single Zone receiver FM8000-BNC 8 Zone control panel FM8000-BNC 8 Zone control panel R1B Plug in receiver R1B Plug in receiver FSM Engineers test receiver FSM Engineers test receiver None of the these? None of the these?

12 SB Swivel bracket for external pirs SB Swivel bracket for external pirs BAT1 12Volt 2.1 Ampere hour battery BAT1 12Volt 2.1 Ampere hour battery BAT2 9Volt alkaline battery BAT2 9Volt alkaline battery BAT3 9Volt lithium battery BAT3 9Volt lithium battery DSA1 Dummy bell box DSA1 Dummy bell box 2100 SD1+ autodialler 2100 SD1+ autodialler SA1 External bell box 6501 Transistor relay module 6501 Transistor relay module 6143 Mains relay timer unit 6143 Mains relay timer unit HG2 Directional antenna HG2 Directional antenna 145-HPWP Corridor PIR 145-HPWP Corridor PIR HG1 High gain antenna HG1 High gain antenna 125-HPWP General purpose PIR 125-HPWP General purpose PIR HS2 Straight stub antenna HS2 Straight stub antenna HS1 Right angle stub antenna HS1 Right angle stub antenna None of the these? None of the these?

13 142012 inertia sensor 142012 inertia sensor BAT640 40 x BAT6 Better Price BAT640 40 x BAT6 Better Price BAT 525 25 x BAT5 Better Price BAT 525 25 x BAT5 Better Price BAT7 12Volt for Ramtech BAT5 Lithium coin cell BAT5 Lithium coin cell BAT6 1.5Volt AA cell BAT6 1.5Volt AA cell BAT4 12Volt N-cell battery BAT4 12Volt N-cell battery BAT240 240 x BAT2 Better price BAT240 240 x BAT2 Better price BAT100 100 x BAT2 Better price BAT100 100 x BAT2 Better price None of the these? None of the these? Escape to main Menu Escape to main Menu Back to start of list. Back to start of list. LENSPACK 2 alternative lenses LENSPACK 2 alternative lenses

14 Ring Technical Support at FM Electronics for further assistance on 01594 827070. Return to previous page Return to previous page Exit to Main Menu Exit to Main Menu

15 4600-GB Infra-red detector 4600-GB Infra-red detector 4650-GB Contact Transmitter 4650-GB Contact Transmitter 4655 Inertia transmitter 4655 Inertia transmitter 4660-GB Smoke Detector 4660-GB Smoke Detector Detection Devices Set/Unset Devices 4173-GB Remote control 4173-GB Remote control 4180 Radio Keypad 4180 Radio Keypad Exit to main menuBack to FM4000X menuAccessories 4005 Tamper Module 4005 Tamper Module 4007 Remote Antenna 4007 Remote Antenna

16 4650-GB Contact Transmitter Designed to detect the opening of doors, windows etc. This unit has a built in back tamper, lid tamper & reed switch that can be used with a magnet of your choice. Please note a magnet is not supplied with this unit. Dimensions 40mm wide x 160mm tall x 28mm deep approx. Can be connected to any normally closed detection device with a normally closed tamper loop. Can be connected to any normally open push to set, where a push to set button is required. Can be used for both push to set and detection at the same time. Powered by 2 AA batteries, our part number BAT6 Exit to main menuExit to previous slide

17 4660-GB Optical Smoke Detector This OPTICAL (sometimes known as photoelectronic) smoke detector is usually better than an ionisation type smoke detector as this detection device will not react as readily to nuisance alarms (cooking fumes etc.) this type of detector reacts best to slow smouldering fires. The detector head conforms to BS5446 part 1-1990 The detector is powered by a 9V PP3 size alkaline battery our part no BAT2. The transmitter is powered by 2 AA batteries, our part number BAT6. (Note. our fire detection system does not conform to BS5839) Exit to main menuExit to previous slide

18 4600-GB General Purpose PIR Dimensions 63mm wide x 110mm tall x 60mm deep approx. 12 metre 90 degree general purpose pir. This unit has 3 pulse count selection options, with a choice of single, 2 or 4 pulses required to generate an alarm condition. Ideal mounting height = 2.2 metres (max.= 2.5 metres.) 2 interchangable lenses are available for this unit. (see LENSPACK below) Powered by 2 AA batteries, our part number BAT6 Batteries should be changed annually. Exit to main menuExit to previous slide LENSPACK

19 LENSPACK 2 Interchangeable lenses for the 4000 series PIRs Lens 1: A 10 metre horizontal curtain lens (sometimes known as a pet alley). When this lens is fitted and the pcb inside the detector is positioned as far down as the tilt adjustment will allow, this detector will ignore any movement below the height at which it is mounted. Not suitable for use where the pet may climb to higher surfaces. (FM part no 366 009) Lens 2: A 25 metre corridor lens, with 4 creep zones. (FM part no. 366 008) Exit to main menuExit to previous slide

20 4600-GB General Purpose PIR Dimensions 63mm wide x 110mm tall x 60mm deep approx. 12 metre 90 degree general purpose pir. This unit has 3 pulse count selection options, with a choice of single, 2 or 4 pulses required to generate an alarm condition. Ideal mounting height = 2.2 metres (max.= 2.5 metres.) 2 interchangable lenses are available for this unit. (see LENSPACK below) Powered by 2 AA batteries, our part number BAT6 Batteries should be changed annually. Exit to main menuExit to previous slide LENSPACK

21 4655 Inertia Transmitter Designed to detect the vibration caused by the forcing open of doors, windows etc. Dimensions : transmitter 40mm wide x 160mm tall x 28mm deep - sensor 20mm x 45mm x 15mm deep + 2metres of cable. Sensitivity adjustment inside unit with an LED to indicate vibration required to activate the unit. Supplied with 1 sensor. For optimum system performance use 1 transmitter with 1 sensor. An additional sensor can be wired in series if required, our part no. 142012. (2 sensors per transmitter is the maximum recommended). Powered by an alkaline PP3 battery, our part number BAT2 Exit to main menuExit to previous slide 142012 Sensor

22 4173-GB Remote Control 3 button remote control, designed to unset, part set, fully set or activate a Panic alarm on any 4000 series control panel. The panic is activated by pressing the unset and the full set buttons together. Green LED on the front of the unit illuminates when the unit is operated to indicate the battery is still serviceable. Batteries typically will last 2 years in normal use. Powered by 2 CR2032 batteries, our part number BAT5. Exit to main menuExit to previous slide

23 4600-GB General Purpose PIR Dimensions 63mm wide x 110mm tall x 60mm deep approx. 12 metre 90 degree general purpose pir. This unit has 3 pulse count selection options, with a choice of single, 2 or 4 pulses required to generate an alarm condition. Ideal mounting height = 2.2 metres (max.= 2.5 metres.) 2 interchangable lenses are available for this unit. (see LENSPACK below) This device is supervised at approximately 20 minute intervals. Powered by 2 AA batteries, our part number BAT6, battery life 1 year. Exit to main menuExit to previous slide LENSPACK

24 4180 Radio Keypad A radio keypad designed to unset, part set, fully set or activate a Panic alarm on any 4000 series control panel. The panic is activated by pressing any two vertical keys from the top three rows together. Green LED on the front of the unit illuminates when the unit is operated to indicate a correct code has been entered. An audible warning will sound from the keypad if the keypad battery is near to the end of its service life. Batteries typically will last 1 year in normal use. Powered by a quality alkaline PP3 size battery, our part number BAT2 Exit to main menuExit to previous slide

25 4100-GB General Purpose PIR Dimensions 63mm wide x 110mm tall x 60mm deep approx 12 metre 90 degree general purpose pir. This unit has 3 pulse count selection options, with a choice of single, 2 or 4 pulses required to generate an alarm condition. Ideal mounting height = 2.2 metres (max.= 2.5 metres.) 2 interchangable lenses are available for this unit. (see LENSPACK below) Powered by 2 AA batteries, our part number BAT6 Batteries should be changed annually. Exit to main menuExit to previous slide LENSPACK

26 4150-GB Contact Transmitter Designed to detect the opening of doors, windows etc. This unit has a built in back tamper, lid tamper & reed switch that can be used with a magnet of your choice, note a magnet is not supplied with this unit. Dimensions 40mm wide x 160mm tall x 28mm deep approx Can be connected to any normally closed detection device with a normally closed tamper loop. Can be connected to any normally open push to set, where a push to set button is required. Can be used for both push to set and detection at the same time. Powered by 2 AA batteries, our part number BAT6 Exit to main menuExit to previous slide

27 4155 Inertia Transmitter Detects the vibration caused by forcing doors, windows etc. Dimensions : transmitter 40mm wide x 160mm tall x 28mm deep - sensor 20mm x 45mm x 15mm deep + 2 metres of 4 core alarm cable Sensitivity adjustment inside unit with an LED to indicate vibration required to activate the unit. Supplied with 1 sensor. For optimum system performance use 1 transmitter with 1 sensor. An additional sensor can be wired in series if required, our part no. 142012. (2 sensors per transmitter is the maximum recommended). Powered by an alkaline PP3 battery, our part number BAT2 Exit to main menuExit to previous slide 142012 Sensor

28 4160-GB Optical Smoke Detector This OPTICAL (sometimes known as photoelectronic) smoke detector is usually better than an ionisation type smoke detector as this detection device will not react as readily to nuisance alarms (cooking fumes etc.). This type of detector reacts best to slow smouldering fires. The detector head conforms to BS5446 part 1-1990 The detector part of this unit is powered by a 9V PP3 size alkaline battery. Our part no BAT2. The transmitter part of this unit is powered by 2 AA batteries, our part number BAT6 (Please note our fire detection system does not conform to BS5839). (Probably better to use 4660-GB for fire systems.) Exit to main menuExit to previous slide

29 Back to previous pageExit to Main Menu FM8000 Control Panel 8 Zone Control Panel + Fire & Panic zones Can accept any number set/unset devices (keypads and/or remote controls in any combination) Dimensions 270mm wide x 155mm tall x 80mm deep. Requires a 12V 2.1Ah battery. Our part no. BAT1. Connections = Mains supply, clean contact relays for external sounder, strobe & Autodialler (SD1+, Vocalizer etc.) 12 Volt Auxiliary power supply rated at 0.5Amp continuous 1 amp intermittent. The radio range from the detection devices to the panel should be checked before each installation (Maximum 500 metres) Devices for this panel

30 4100-GB Infra-red detector 4100-GB Infra-red detector 4150-GB Contact Transmitter 4150-GB Contact Transmitter 4155 Inertia transmitter 4155 Inertia transmitter 4160-GB Smoke Detector 4160-GB Smoke Detector Detection Devices Set/Unset Devices 4173-GB Remote control 4173-GB Remote control 4180 Radio Keypad 4180 Radio Keypad Exit to main menuBack to Previous slideAccessories 4007 Remote Antenna 4007 Remote Antenna

31 4005 Antenna Tamper Module (For 4007 Antenna) All antennas connected to CLASS 6 systems must be tamper protected, either mechanically, electronically or by any combination of the two techniques. This tamper module checks the integrity of the connection between the antenna and the module, creating a tamper fault if this connection is lost. The unit is designed to be connected in series with the tamper loop, generating a tamper fault on the control panel if this connection is lost. There is an indicator fitted to the module to indicate to the engineer the tamper fault originates from the antenna module. Fits inside any of the FM4000 series panels. Exit to main menuExit to previous slide 4007 Antenna

32 4007 Remote Antenna A dipole antenna suitable for use with the 4005 module on Class 6 systems or on its own on Class 3 systems. Supplied with 10 metres of co-axial cable, which should be cut to the minimum length required at the point of installation. The cable should never be extended or joined. When a remote antenna is used, the antenna inside the control panel should be disconnected (preferably removed completely). The Antenna should be mounted vertically (one end is labelled TOP), the cable should come out at 90 degrees to the antenna and must not run against the antenna housing especially the top part of the antenna. Exit to main menuExit to previous slide 4005 Module

33 FM4000E 8 Zone Control Panel + Fire & Panic zones plus up to 8 set/unset devices (keypads or remote controls in any combination) Dimensions 270mm wide x 155mm tall x 80mm deep. Requires a 12V 2.1Ah battery. Our part no. BAT1. Connections = For mains supply, external sounder & Autodialler. Absolute maximum working range from furthest device to the control panel 100 metres (this is measured in free space.) The actual maximum working range achieved will vary from site to site and signal strength should be checked before installation is commenced. Devices for this panelExit to Main Menu Checking signal strength

34 FM8000 series Panels RP2 Repeater station RP2 Repeater station 8008 8 zone receiver 8008 8 zone receiver FM8016 Indicator panel FM8016 Indicator panel R1 Single zone receiver R1 Single zone receiver FM8000-BNC 8 Zone control panel FM8000-BNC 8 Zone control panel R1B Plug in receiver R1B Plug in receiver FSM Engineers test receiver FSM Engineers test receiver Receiver / Interfaces Test Equipment Repeater External panel/receiver selector.

35 Back to previous menu Exit to Main Menu FM8016 FM8016 Indicator Panel 14 zones, tamper & low battery indication This panel is typically used with panic buttons or smoke detectors, where 24 hour protection is required. Dimensions 270mm wide x 155 tall x 80mm deep. Requires a 12V 2.1Ah battery. Our part no. BAT1. Connections = Mains supply, clean contact relays for external sounder, strobe & Autodialler (SD1+, Vocalizer etc.) 12Volt Auxiliary power supply rated at 0.5Amp continuous 1 amp intermittent. Devices for this panel

36 Do you require a FOB (Push button transmitter) for the 4000 series or the 8000 series? 4000 Series8000 Series

37 4173-GB You require the 4173-GB, 3 button remote control. Back to main menuBack system select menu More information about this device

38 Do you require a single button unit or a four button unit? Single Button Four Button

39 TR4-HP You require a TR4-HP Back to main menuBack system select menu More information about the TR4-HP

40 Do you require a hand held unit or a pendant (necklace type) unit? Hand heldPendant

41 TPHP The part number you require is TPHP Back to main menuBack to system select menu More information about this device

42 PEN 173 The part number you require is PEN 173 NOTE:- YOU MUST KNOW THE SITE CODE AND THE ZONE NUMBER. BEFORE ORDERING THIS UNIT THESE ARE FACTORY PRESET AND NOT USER AJUSTABLE. IF IN DOUBT CONTACT TECHNICAL SUPPORT AT FMELECTRONICS ON 01594 827070 Back to main menuBack to system select menu More information about this device

43 TR4-HP Remote Control 4 button remote control, designed to unset, part set, full set or activate a Panic alarm on the FM8000 control panel. The buttons from left to right are Unset (Black), Part Set (Grey), Full Set (grey) & Panic (red), these buttons are protected by a sliding cover to prevent accidental operation. Green LED on the front of the unit illuminates when the unit is operated to indicate the battery is still serviceable Typically the battery will last 1 year in normal use. Powered by 1 quality alkaline PP3 size battery, our part number BAT2 Maximum radio range 500 metres, the maximum will vary from site to site and should be checked at each installation. Exit to main menuExit to previous slide

44 TPHP Hand held Panic Transmitter Operated by a single Red button, which can be protected from accidental operation by a sliding cover. The unit can be user programmed to send any site code and zone to any receiver in the 8000 series product range. Green LED on the front of the unit illuminates when the unit is operated to indicate the battery is still serviceable Typically the battery will last 1 year in normal use. Powered by 1 quality alkaline PP3 size battery, our part number BAT2 Absolute maximum radio range 500 metres. (This is under ideal conditions), the actual range achieved will vary from site to site and should be checked at each installation. Exit to main menuExit to previous slide

45 PEN173 Pendant Panic Transmitter Operated by pressing a single button, on the front of the unit or by breaking the neck cord. The unit is FACTORY PROGRAMMED to send the required site code and zone. (We MUST know which SITE CODE & ZONE is required, before an order is placed). Green LED on the front of the unit illuminates when the unit is operated to indicate the battery is still serviceable Powered by 1 Quality Alkaline N cell, our part number BAT4 this will last 1 year in normal use. Absolute maximum radio range 100metres. (This is under ideal conditions), the actual range achieved will vary from site to site, and should be checked at each installation. Exit to main menuExit to previous slide

46 Remote Controls & Keypads. 10GP General purpose transmitter 10GP General purpose transmitter 115H-HPWP 10 Metre horizontal PIR 115H-HPWP 10 Metre horizontal PIR DK3-HP Radio keypad DK3-HP Radio keypad 125-HPWP 12 Metre general purpose PIR 125-HPWP 12 Metre general purpose PIR TR4-HP Remote control TR4-HP Remote control 145-HPWP 35 metre corridor PIR 145-HPWP 35 metre corridor PIR Select your panic button here Select your panic button here Detection Devices Panic Buttons

47 Do you require a hand held unit or a pendant (necklace type) unit? Hand heldPendant

48 TPHP The part number you require is TPHP Back to main menuBack to controls, panic & detection devices. More information about this device

49 Back to controls, panic & detection devices. PEN 173 The part number you require is PEN 173 NOTE:- YOU MUST KNOW THE SITE CODE AND THE ZONE NUMBER. BEFORE PLACING AN ORDER FOR THIS UNIT THESE ARE FACTORY PRESET AND NOT USER AJUSTABLE. IF IN DOUBT CONTACT TECHNICAL SUPPORT AT FM ELECTRONICS ON 01594 827070 Back to main menu More information about this device

50 DK3-HP Radio Keypad A radio keypad designed to unset, part set, full set or activate a Panic alarm on the FM8000 control panel. The panic is activated by pressing any two vertical keys from the top two rows together. Green LED on the front of the unit illuminates when the unit is sending its signal to the control panel. An audible warning will sound from the keypad if the battery is near to the end of its service life. The Battery typically will last 1 year in normal use. Powered by a quality alkaline PP3 size battery, our part number BAT2 Exit to main menuExit to previous slide

51 115H-HPWP Horizontal curtain PIR Dimensions 80mm wide x 160mm tall x 58mm deep approx. (excluding Antenna). 10 metre 90 degree horizontal curtain pir, sometimes known as a Pet Alley detector. Suggested mounting height = 1.5 metres, note if this unit is mounted too high, it may be possible to walk through an area without being detected Powered by 1 PP3 battery, our part number BAT2 Battery should be changed annually. Maximum radio range 500 metres in ideal conditions, the actual working achieved will vary from site to site and should be checked at each installation. Exit to main menuExit to previous slide

52 125-HPWP General Purpose PIR Dimensions 80mm wide x 160mm tall x 58mm deep approx. (excluding Antenna) 12 metre 90 degree general purpose pir Suggested mounting height = 2.2 metres, maximum mounting height = 2.5 metres. Note if this unit is mounted too high, it may be possible to walk through without being detected. Powered by 1 PP3 battery, our part number BAT2 Battery should be changed annually. Maximum radio range 500 metres in ideal conditions, the actual working achieved will vary from site to site and should be checked at each installation. Exit to main menu Exit to previous slide

53 145-HPWP Corridor PIR Dimensions 80mm wide x 160mm tall x 58mm deep approx. (excluding Antenna) 35 metre corridor pir. Suggested mounting height = 2.2 metres, maximum mounting height = 2.5 metres. Note if this unit is mounted too high, the maximum detection range will not be achieved. Powered by 1 PP3 battery, our part number BAT2. Battery should be changed annually. Maximum radio range 500 metres in ideal conditions, the actual working achieved will vary from site to site and should be checked at each installation. Exit to main menuExit to previous slide

54 10GP General Purpose Transmitter Dimensions 80mm wide x 125mm tall x 58mm deep approx. excluding antenna and cable entry gland. 10 milli Watt general purpose transmitter. Can be triggered by any normally open or any normally closed device. Powered by a 12V DC power supply OR 1 PP3 battery, our part number BAT2. Battery should be changed annually. Maximum radio range 500 metres in ideal conditions, the actual working achieved will vary from site to site and should be checked at each installation. Exit to main menuExit to previous slide

55 R1 Single Zone Receiver Dimensions 80mm wide x 150mm tall x 50mm deep approx. excluding antenna. Clean Contact change over relay, can be programmed to latch or change over momentarily in alarm. The relay will switch a maximum of 1 amp, (and 28 Volts). Powered by a 12VDC power supply, typically draws 70milli amps. Generally used to add a panic button to a hard wired alarm system. Supplied with a BNC connector and helical stub antenna, remote antennas (HG1 & HG2) can be used with this receiver if required. Exit to main menuExit to previous slide

56 R1B Single Zone Receiver Sounder Dimensions 80mm wide x 150mm tall x 50mm deep approx. excluding antenna & power supply. Contains a piezo sounder which can be either momentary or latching in alarm. Simply plugs into the mains. Generally used for annunciation purposes with PIR's or as a warning device with panic buttons Supplied with a BNC connector and helical stub antenna, remote antennas (HG1 & HG2) can be used with this receiver if required. Exit to main menuExit to previous slide

57 8008 General Purpose Receiver Dimensions 113mm wide x 164mm tall x 40mm deep approx. excluding antenna. Contains 8 clean contact relays which can be normally closed or open in alarm. Max current 1amp (28 Volts Max.) Requires a 12 Volt supply, draws 17 milli amps with all relays relaxed & a maximum of 300 milli amps with all the relays energised. Generally used as an interface to hard wired alarm systems, the outputs are programmable so may be suitable for other applications. Supplied with a BNC connector and helical stub antenna, remote antennas (HG1 & HG2) can be used with this receiver if required. Exit to main menuExit to previous slide

58 You require the FM4000 series product How many zones do you require? Up to 8 zones (circuits) Up to 8 zones (circuits) Up to 64 zones (circuits) Up to 64 zones (circuits) More than 64 zones (circuits) More than 64 zones (circuits)

59 FM4000X & FM4001(used together) 64 Zone Control Panel + 8 Fire & 8 Panic zones plus up to 8 set/unset devices (keypads or remote controls in any combination) Dimensions 270mm wide x 320mm tall x 80mm deep approx. Requires a 12V 2.1Ah battery. Our part no. BAT1. Connections required = Mains supply, external sounder & communications as required Absolute maximum working range from furthest device to the control panel 100 metres (this is measured in free space.) The actual maximum working range achieved will vary from site to site and signal strength should be checked before installation is commenced. Devices for this panelExit to Main Menu Checking signal strength

60 FSM Field Test Receiver Dimensions 80mm wide x 150mm tall x 50mm deep approx. excluding antenna. Suitable for use with the FM8000 series products only. Powered by a quality Alkaline PP3 size battery, our part no. BAT2. Battery OK indicator on the front of unit no longer illuminates in use, when the battery needs replacing. Indicates data valid & zone transmitted from the transmitting device, a valuable addition to an engineers toolkit. Supplied with a BNC connector and helical stub antenna, remote antennas (HG1 & HG2) can be connected to this test receiver if required. Exit to main menuExit to previous slide

61 Back to previous pageExit to Main Menu RP2 Repeater Repeats all signals used on FM8000, 8016, 8008, R1 & R1B (includes set-unset signals from remote controls & keypads) Receives signals on 1 house code and transmits the signal on to the control panel on a different hose code. Dimensions 270mm wide x 155 tall x 80mm deep. (excluding aerials) Requires a 12V 2.1Ah battery. Connections = Mains supply, 2 x BNC connectors for antennas, 2 stub antennas supplied, remote antennas HG1 or HG2 may be used if appropriate. ( Contact Technical Support at FM Electronics on 01594 827070 for advise on antenna selection if unsure)

62 Find a part by description. Interfaces / Receivers Interfaces / Receivers Control Panels Control Panels Keypads Contacts / Transmitters Contacts / Transmitters Aerials Batteries Relays / Timers Relays / Timers Infra Red Detectors Infra Red Detectors Back to main menu Back to main menu Remotes, PAs FOBs etc. Remotes, PAs FOBs etc. Repeater

63 Find a part by description. An internal intruder alarm system? An internal intruder alarm system? An external intruder alarm system? An external intruder alarm system? Do you require a control panel for

64 Find a part by description. Monitored with police response? Monitored with police response? Local audible (bells) only? Local audible (bells) only? Do you require the system to be

65 Find a part by description. Operate like a conventional alarm system with set / unset facilities? Operate like a conventional alarm system with set / unset facilities? To be a display which will operate and sound every time a device is activated? To be a display which will operate and sound every time a device is activated? Do you require the system to

66 Find a part by description. The only repeater we have is the RP2 for the 8000 series panel RP2 Repeater RP2 Repeater

67 TSD-HP Optical Smoke Detector This OPTICAL (sometimes known as photoelectronic) smoke detector is usually better than an ionisation type smoke detector, as this detection device will not react as readily to nuisance alarms (cooking fumes etc.), this type of detector reacts best to slow smouldering fires. The detector head conforms to BS5446 part 1-1990 The detector is powered by 2 x 9V PP3 size alkaline batteries our part no BAT2. Maximum radio range 500 metres under ideal conditions. (Please note our fire detection system does not conform to BS5839) Exit to main menuExit to previous slide

68 125-HP High Power General Purpose PIR Dimensions 70mm wide x 115mm tall x 38mm deep approx. 12 metre 90 degree general purpose pir, with a maximum radio range of 500 metres under ideal conditions Ideal mounting height = 2.2 metres (max.= 2.5 metres.) Suitable for use with FM8000, FM8016, 8008, R1 or R1B, receivers or control panels. Powered by a PP3 size quality alkaline battery, our part number BAT2 Batteries should be changed annually. Exit to main menuExit to previous slide

69 HG1 High Gain Antenna The HG1 is a Co-linear antenna with a 2dB gain for use with the FM8000, FM8016, 8008, R1 and R1B. This antenna can also be used with some other products, contact Technical Support at FM Electronics on 01594 827070 to check suitability. The working range of the system can usually be increased by mounting this antenna at a high level externally. Supplied with 10 metres of co-axial cable and a BNC socket, this cable should not be cut or extended. Supplied with a mounting clamp suitable for 1 and a half to 2 inch mast. (3.8 - 5 cm approx.) Exit to main menuExit to previous slide

70 HG2 Directional Antenna The HG2 is a directional antenna with a 8dB forward gain for use with the FM8000, FM8016, 8008, R1 and R1B. This antenna can also be used with some other products, contact Technical Support at FM Electronics on 01594 827070 to check suitability. The working range of the system can usually be approximately doubled to a maximum of 1 km by mounting this antenna at a high level externally. Supplied with 10 metres of co-axial cable and a BNC socket, we strongly recommend this cable length is not exceeded. Supplied with a mounting clamp suitable for 1 and a half to 2 inch mast. (3.8 - 5 cm approx..) Exit to main menuExit to previous slide

71 HS1 Right Angled Stub Antenna The HS1 is normally supplied as a replacement antenna for use with any device fitted with a BNC socket which is on the side of the unit the unit is in use. All antennas should be vertical in normal use. (Note if the BNC socket is on the top of the unit a HS2 straight stub antenna should be used.) Exit to main menuExit to previous slide

72 HS2 Straight Stub Antenna The HS2 is normally supplied as a replacement antenna for use with any device fitted with a BNC socket which is on the top of the unit when the unit is in use. All antennas should be vertical in normal use. (Note if the BNC socket is on the side of the unit a HS1 right angled stub antenna should be used.) Exit to main menuExit to previous slide

73 6143 Mains Relay Timer The 6143 mains relay timer will switch a maximum of 240 Volts ac witha1000 watts (resistive load), from a 12Vdc trigger. The relay can be timed to operate between 2 & 30 minutes. Can be used as a mains relay without the timer function if required to simply follow the input. Can be used with a momentary or latching input. Timer can be set up to run until the input is removed or timer expires, whichever is sooner Requires a 12V dc power supply. Exit to main menuExit to previous slide

74 6501 Transistor Relay Module The 6501 relay module will switch a maximum of 1 amp at 28Volts dc. The relay can be triggered with as little as 5Volts. Only 1milli Amp required to drive the relay trigger. 2 clean contact change over relays available. Requires a 12V dc power supply. Exit to main menuExit to previous slide

75 SA1 External Bell Box The SA1 is a self activating external sounder and strobe unit with a built in back up battery. The unit we currently supply is the Volumatic Xtra in Yellow with a White strobe window. This unit can be configured as either a Self Activating Bellbox (SAB) or a Self Contained Bellbox (SCB). The bell box has 2 Led's which flash alternately when the unit is powered up. (The Led's simply flash continuously, they do not indicate whether the system is armed or disarmed). Exit to main menuExit to previous slide

76 DSA1 Dummy External Bell Box The DSA1 is a bell box cover with wall mounting bracket.. The unit we currently supply is the Volumatic Xtra cover and bracket. This box is mainly yellow, with a white window area in the bottom of the unit. This unit makes no noises and has no lights in it. Exit to main menuExit to previous slide

77 2100 Menvier SD1+ Speech Dialler The SD1+ can store up to 4 telephone numbers and when activated re-play a message up to 40 seconds in length. The SD1+ has a non volatile memory, so even if the power is disconnected, no stored information will be lost. The unit can send up to 4 separate alarm messages, with the 4 separate trigger inputs available A 4 digit passcode is required before any programming can be changed. (Default code = 1234) The unit can dial any normal telephone number, most mobile telephone numbers (some phones on the ORANGE network will not work with this unit), some paging units can also be dialled by this unit. Exit to main menuExit to previous slide

78 SB Swivel Bracket The SB swivel bracket can be used with any External Infra Red detector (the ones in the grey plastic housings) produced by FM Electronics. The bracket is an L shape, and should be mounted into the base of the external detector. Exit to main menuExit to previous slide

79 BAT1 12Volt Lead Acid Battery The BAT1 is a 12 Volt 2.1 Ampere hour sealed lead acid battery. This battery is used in all FM4000 series and FM8000 series control panels 1 Battery is normally used per unit. (Note 2 batteries are required when the FM4000X & FM4001 units are used together.) Exit to main menuExit to previous slide

80 BAT2 9Volt Alkaline Battery The BAT2 is a 9 Volt PP3 size alkaline battery, this battery will fit all the transmitters used in the FM8000 series and the 4155, 4180, 4190, 4193 & 4655, devices currently used in the FM4000 series, also all smoke detector heads (but not necessarily the transmitter part of the detector). This battery was used in all the transmission devices used for the 4000 series before 1999, during this year the new -GB products were introduced, and different batteries have typically been used. When purchased in larger quantities the price of this product improves. (See BAT100 & BAT 240) Exit to main menuExit to previous slide

81 BAT3 9Volt Lithium Battery The BAT3 is a 9 Volt PP3 size Lithium battery, THIS BATTERY IS NO LONGER USED. This battery this battery was originally specified for all class 6 detection devices, however the manufacturer of this battery changed the specification of this battery in 1997. We now recommend the BAT2 for applications where this battery was originally specified. Exit to main menuExit to previous slide GO TO BAT2 GO TO BAT2

82 BAT4 12Volt N cell Battery The BAT4 is a 12 Volt N cell battery, This battery is used in the PEN173 transmitter only. When replacing the battery in the PEN 173 ensure the new battery is making a good connection with the battery tags inside the PEN173. If necessary bend the battery tags slightly towards the centre of the unit to make a tighter connection. Exit to main menuExit to previous slide

83 BAT5 CR2032 Lithium Coin cell Battery The BAT5 is a lithium coin cell battery for use in the 4173-GB remote control unit. 2 batteries are required for each 4173-GB remote control. Exit to main menuExit to previous slide

84 BAT6 1.5 Volt AA Size Battery The BAT6 is an alkaline AA size battery. 2 batteries are required for each of the devices we supply which use this battery. The following units use these batteries, 4100-GB, 4150-GB, 4160-GB (Transmitter only), 4600-GB, 4650-GB, 4660-GB (Transmitter only). Exit to main menuExit to previous slide

85 BAT7 12 Volt Battery for Ramtech Receiver. The BAT7 is Lead Acid battery with a flying connection lead for use in the Ramtech special receiver. 1 Battery is required per receiver. Exit to main menuExit to previous slide

86 BAT100 - 100 x BAT2. 100 x 9Volt quality alkaline batteries, the price is reduced with the volume purchased. Exit to main menuExit to previous slide See BAT2

87 BAT240 - 240 x BAT2. 100 x 9Volt quality alkaline batteries, the price is reduced with the volume purchased. Exit to main menuExit to previous slide See BAT2

88 BAT525 - 25 x BAT5. 25 x 3Volt CR2032 Lithium coin cell batteries, the price is reduced with the volume purchased. Exit to main menuExit to previous slide See BAT5

89 BAT640 - 40 x BAT6. 40 x 1.5Volt quality alkaline AA size batteries, the price is reduced with the volume purchased. Exit to main menuExit to previous slide See BAT6

90 142012 Aritech Sensor for Inertia Transmitters The 142012 sensor can be used in addition to or as a replacement, with any of the Inertia transmitters supplied by us. Ideally 1 sensor per transmitter, however usually 2 sensors can be used provided both sensors are located on similar materials in both density and size, Contact Technical Support at FM Electronics on 01594 827070 to check suitability. Part numbers of transmitters which have used this sensor include: 4155, 4655, TMA, and TMA-HP. Exit to main menuExit to previous slide

91 Find a part by description. To add to the 4000 series intruder alarm system? To add to the 4000 series intruder alarm system? To add to the 8000 series intruder alarm system? To add to the 8000 series intruder alarm system? Do you require an aerial To replace an original antenna? To replace an original antenna?

92 Find a part by description. Fitted directly onto the transmitter or receiver? Fitted directly onto the transmitter or receiver? Used away from the transmitter or receiver? Used away from the transmitter or receiver? Will the antenna be

93 Find a part by description. On the side of the transmitter or receiver? On the side of the transmitter or receiver? On the top of the transmitter or receiver? On the top of the transmitter or receiver? Is the BNC socket for the aerial

94 Find a part by description. Class 3 system (local Audible Only) Class 3 system (local Audible Only) Class 6 system (Police response) Class 6 system (Police response) Is the system a Class 3 (Local Audible Only)or Class 6 (Police Response) system

95 Find a part by description. A 4000 series Class 3 system (local Audible Only) A 4000 series Class 3 system (local Audible Only) A 40000 series Class 6 system (Police response) A 40000 series Class 6 system (Police response) Is the aerial to be used with An 8000 series control panel An 8000 series control panel

96 Find a part by description. external antenna which will receive a signal from any direction (Omnidirectional) external antenna which will receive a signal from any direction (Omnidirectional) external antenna which will receive a signal from one direction only (Directional) external antenna which will receive a signal from one direction only (Directional) Is the aerial to be used an

97 Find a part by description. Part of an FM4000 System Part of an FM4000 System Part of an FM8000 System Part of an FM8000 System Is the detector to be used as

98 Find a part by description. Internally (we only have one option) Internally (we only have one option) Externally Is the detector to be used

99 Find a part by description. 10 Metre 90 degree Horizontal Curtain 10 Metre 90 degree Horizontal Curtain 35 Metre corridor beam 35 Metre corridor beam Which detection pattern do you require? 12 Metre 90 degree General Purpose Pattern 12 Metre 90 degree General Purpose Pattern

100 Find a part by description. As part of a Class 3 system (Audible only) As part of a Class 3 system (Audible only) As part of a Class 6 system (Police Response As part of a Class 6 system (Police Response Is the detector to be used

101 Find a part by description. Internally Externally Is the detector to be used

102 Find a part by description. A detector should not be used externally with a Class 6 system, particularly where the system is connected to a central station for Police response. Contact Technical Support at FM Electronics on 01594 827070 for more information. Back to find product by description Back to the main menu

103 4193 Corridor PIR Dimensions 80mm wide x 160mm tall x 58mm deep approx. (excluding Antenna) 30 metre corridor pir. Suggested mounting height = 2.2 metres, maximum mounting height = 2.5 metres. Note if this unit is mounted too high, the maximum detection range will not be achieved. Powered by 1 PP3 battery, our part number BAT2 Battery should be changed annually. Maximum radio range 500 metres in ideal conditions, the actual working achieved will vary from site to site and should be checked at each installation. Exit to main menuExit to previous slide

104 4190 General Purpose PIR Dimensions 80mm wide x 160mm tall x 58mm deep approx. (excluding Antenna) 12 metre 90 degree general purpose pir Suggested mounting height = 2.2 metres, maximum mounting height = 2.5 metres. Note if this unit is mounted too high, it may be possible to walk through without being detected. Powered by 1 PP3 battery, our part number BAT2 Battery should be changed annually. Maximum radio range 500 metres in ideal conditions, the actual working achieved will vary from site to site and should be checked at each installation. Exit to main menuExit to previous slide

105 Find a part by description. Internally Externally Is the detector to be used

106 Find a part by description. 12 Metre 90 Degree general purpose 12 Metre 90 Degree general purpose 30 Metre Corridor 30 Metre Corridor Which detection pattern would you prefer?

107 4100-GB General Purpose PIR Dimensions 63mm wide x 110mm tall x 60mm deep approx 12 metre 90 degree general purpose pir. This unit has 3 pulse count selection options, with a choice of single, 2 or 4 pulses required to generate an alarm condition. Ideal mounting height = 2.2 metres (max.= 2.5 metres.) 2 interchangable lenses are available for this unit. (see LENSPACK below) Powered by 2 AA batteries, our part number BAT6 Batteries should be changed annually. Exit to main menuExit to previous slide LENSPACK

108 Find a part by description. A Control Panel, repeater or test receiver ? A Control Panel, repeater or test receiver ? A Three button remote control (4173-GB)? A Three button remote control (4173-GB)? Do you require a battery for A Pendant transmitter (PEN 173)? A Pendant transmitter (PEN 173)? Any other device not listed above? Any other device not listed above?

109 Find a part by description. FM4000E Which item do you require a battery for FM4000 FM4000X FM4001 FM8000 FM8016 RP2 Repeater RP2 Repeater SP311 (receiver for Ramtech) SP311 (receiver for Ramtech) FSM Test Receiver FSM Test Receiver None of these? None of these?

110 Find a part by description. 4100-GB Which item do you require a battery for 4150-GB 4155 4180 4160-GB 4190 4193 4600-GB 4650-GB 4655 4660-GB 125-HP 125-B 145-B 115H-HPWP 125-HPWP 145-HPWP NONE OF THESE? NONE OF THESE? 10GP TPHP TR4-HP

111 Find a part by description. BAT6 For Transmitters not previously listed, as a general rule if the part number has -GB after it the unit will require a BAT6, all other items a BAT2 will most probably be required. BAT2

112 Find a part by description. C6 Six zone control panel (1985 - 1990 approx) C6 Six zone control panel (1985 - 1990 approx) Other control panels not previously listed. C5 Five zone control panel (1986-1991 approx..) C5 Five zone control panel (1986-1991 approx..) For all others contact Technical Support at FM Electronics on 01594 827070. Back to Find Part by Description Menu Back to Find Part by Description Menu

113 Find a part by description. This panel requires a 12 Volt 3 Ampere hour back up battery, we no longer stock this battery, however the a BAT2 can be used but the standby time will be reduced to approximately 14 hours (from 20 hours) Link to BAT1 Link to BAT1 Exit to Main Menu Exit to Main Menu Back to Find Part by Description Menu Back to Find Part by Description Menu

114 Find a part by description. This panel requires a 12V 1.2 Ampere hour battery no longer stocked by FM Electronics. Usually stocked by most security equipment distributors Contact Technical Support at FM Electronics on 01594 827070 for further assistance. Back to Find Part by Description Menu Back to Find Part by Description Menu Back to Main Menu Back to Main Menu

115 Find a part by description. FM4000E Do you require a keypad for the FM4000 FM4000X FM8000 Exit to main menu Exit to main menu Back to Find Part by Description Menu Back to Find Part by Description Menu Note: Our keypads are only compatible with our panels.

116 Find a part by description. An existing 4000 system? An existing 4000 system? Do you require a Contact / Transmitter for An existing 8000 system? An existing 8000 system? Exit to main menu Exit to main menu Back to Find Part by Description Menu Back to Find Part by Description Menu A new system? A new system?

117 Find a part by description. Class 3 system? Class 3 system? Is the system a Class 6 system? Class 6 system? Exit to main menu Exit to main menu Back to Find Part by Description Menu Back to Find Part by Description Menu

118 Find a part by description. Class 3 product with up to 100 metre working range? Class 3 product with up to 100 metre working range? Do you require a Class 6 product with up to 100 metre working range? Class 6 product with up to 100 metre working range? Exit to main menu Exit to main menu Back to Find Part by Description Menu Back to Find Part by Description Menu Class 3 product with up to 500 metre working range? Class 3 product with up to 500 metre working range?

119 Find a part by description. An interface to use radio devices into a wired panel? An interface to use radio devices into a wired panel? Do you require A plug in receiver sounder? A plug in receiver sounder? Exit to main menu Exit to main menu Back to Find Part by Description Menu Back to Find Part by Description Menu A test receiver? A test receiver?

120 Find a part by description. A single zone for use with a panic button or similar? A single zone for use with a panic button or similar? Do you require Up to 6 zones + Tamper & Battery monitoring? Up to 6 zones + Tamper & Battery monitoring? Exit to main menu Exit to main menu Back to Find Part by Description Menu Back to Find Part by Description Menu More than 6 zones? More than 6 zones?

121 Find a part by description. You may be able to use more than 1 six zone receiver to get the required number of zones, contact Technical Support at FM Electronics on 01594 827070 for advice. Link to 6 zones + Tamper & Battery monitoring unit? Link to 6 zones + Tamper & Battery monitoring unit? Exit to main menu Exit to main menu Back to Find Part by Description Menu Back to Find Part by Description Menu

122 Find a part by description. Do you require a Timer which will time between 2 & 30 minutes and switch up to 1000 watts at 240Volts AC? Timer which will time between 2 & 30 minutes and switch up to 1000 watts at 240Volts AC? Exit to main menu Exit to main menu Back to Find Part by Description Menu Back to Find Part by Description Menu Relay to use a logic level output (like a digi output on the 4000 control panel) to switch up to 28volts 1 amp? Relay to use a logic level output (like a digi output on the 4000 control panel) to switch up to 28volts 1 amp?


Download ppt "FM Electronics Product Information & Product Finder I Know the Part Number I Know the Part Number I need POLICE response I need POLICE response 4000 series."

Similar presentations


Ads by Google