We think you have liked this presentation. If you wish to download it, please recommend it to your friends in any social system. Share buttons are a little bit lower. Thank you!
Presentation is loading. Please wait.
Published byMacy Dimmer
Modified over 2 years ago
Building a Weather Station for a Near-Space Payload AEM 1905: Spaceflight with Ballooning University of Minnesota
Weather Station kit and instructions
Parts in Weather Station kit
Printed Circuit Board (PCB)
Wires for sensor cabling
Relative humidity sensor
3 x 3 pin male header for sensor cable
Heat-shrink tubing (AKA shrink-wrap)
Solder resistor in place; snip all excess leads
Solder the capacitor in place
Insert relative humidity sensor, making sure that the open part faces capacitor
Avoid solder bridges on closely-spaced pins of the relative humidity sensor
Insert the temp sensor, watching polarity
Insert pressure sensor, right way around
Strip both ends of each wire, exposing ¼ inch length of the bare metal
Insert one wire through large hole then bend it over and solder – for strain relief
Repeat with other 4 wires – use black for ground and red for +5 volts (at least)
Insert 3 x 3 header into a female receptacle, like that in a BalloonSat Easy computer
Orient 3 x 3 pin header next to the figure to identify which pins to solder wires to
Tin the 5 pins – add a bit of solder quickly
Twist exposed ends of wires then tin them
Slide on shrink-wrap before proceeding. Use blue shrink-wrap, not stuff in kit.
Use Helping Hands to hold wire up to pin
Solder 5 wires to pins, minimizing diameter
Slide shrink-wrap over solder joints once all wires have been soldered
Shrink with heat gun while still plugged in, then remove cable from receptacle
Completed Weather Station; ready to be plugged into a flight computer
Building a Weather Station for a Near-Space Payload AEM 1905: Spaceflight with Ballooning University of Minnesota.
Building a NearSys BalloonSat Easy Flight Computer for a Near-Space Payload AEM 1905: Spaceflight with Ballooning University of Minnesota.
Building a Pressure/Temperature Weather Station (Sensor Pack) AEM 1905, Fall 2008.
Building a Heater Circuit for a Near-Space Payload AEM 1905: Spaceflight with Ballooning University of Minnesota.
Learn-to-Solder Exercise: Practice Flasher Circuit AEM 1905: Spaceflight with Ballooning University of Minnesota.
CricketSat LP (Transmitter) Assembly Instructions This is the instruction slides for the assembly of a transmitter board. This is the board that will fly.
AnaSonde Assembly. What is the AnaSonde? *Reads temperature, pressure, and humidity data from the atmosphere *After it is sent into the atmosphere, it.
UVM CricketSat Assembly Manual. Getting Started Make a hard copy print out of the following page It will help you identify the proper components Place.
Assembling the CheapBot Line Follower In 8 easy steps.
AnaSonde-3M Assembly. What is the AnaSonde-3M? The AnaSonde-3M reads temperature, pressure and humidity data from the atmosphere. After the AnaSonde is.
CricketSat Assembly Manual. CricketSat Background Developed at Stanford University –Space Systems Development Laboratory Part of the NASA student satellite.
SpectraSonde Assembly. What is the SpectraSonde? Reads temperature, pressure, and humidity data from the atmosphere. The SpectraSonde doesn’t fly like.
1 Student Hands On Training I (2009) Additional AVR Modifications For BalloonSat Flight Additional AVR Modifications For BalloonSat Flight.
CricketSat Receiver Assembly Instructions This is the instruction slides for the assembly of a receiver board. It would be a good idea to review soldering.
Electronics Merit Badge Class 4 5/17/2015Electronics Merit Badge Class National Scout Jamboree1.
Circuits and Electronics (in a Nutshell) AEM 1905, Fall 2008.
ASSEMBLING THE PCB Have the PCB in front of you as shown. Make sure there are no copper tracks showing. This side is called the component side.
1 Student Hands On Training I (2009) Soldering 101.
Colorado Space Grant Consortium Gateway To Space ASEN / ASTR 2500 Class #06 Gateway To Space ASEN / ASTR 2500 Class #06.
Soldering Building permanent circuits. Soldering accomplishes two things Electrical connections Mechanical connections.
Assembly Manual Mike Fortney 06/26/2006 CricketSat Receiver.
ROV Cameras. Extending Your Camera We want your ROV to be able to see the sea! (And the pool)
Soldering Jumper Wires SPIRIT Strip about ¼” of insulation Apply solder until wire appears soli d “Tin” the wire.
Colorado Space Grant Consortium Timing Circuit HW #4 Class #07 Timing Circuit HW #4 Class #07.
MOOD LIGHT PCB ASSEMBLY V By Phil Townshend 2008.
RockOn! RockOn! Structure Build RockOn! 2009.
1 Hands-on: Heater Circuit Kit includes: 3 9 Volt batteries (for flight only) 1 Perf Board 3Ceramic Resistors (4 5W) 39 V connectors 1 White wire 1.
Assembly Manual Mike Fortney 04/02/2006 CricketSat LC Receiver.
Vex 1.0 © Carnegie Mellon Robotics Academy Inc. CRIMPING Introduction This presentation is the companion to Background / Resources / Crimping Guide slide.
CricketSat Assembly 1. Top side of printed circuit board (PCB) Schematic 2.
Tweaking Your Simon Adding a photoresistor and changing code Instruction by Pete Lewis.
Assembly Manual Mike Fortney 06/26/2006 CricketSat LP.
WIRE REPAIR. TROUBLESHOOTING STEPS l Confirm the Complaint l Study the electrical schematic l Locate and repair the fault l Test the repair.
How to Make ECG Leads Strip 2-3” of insulation –Use an Exacto knife to carefully cut the gray insulation away –Do not cut the metal braided shield underneath.
LSU 09/12/2013Electronics - SkeeterSat1 Building SkeeterSat Inventory Components Identify components Use the parts list and assembly manual Tape to.
Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.
MODULE 6: Soldering SUMMER CHALLENGE Electrical Engineering: Smart Lighting Michael Rahaim, PhD Candidate Multimedia Communications Lab Boston University.
Parts list 1 – 8’ 2” OD stainless steel pipe, chamfered at both ends 1 –7’ 4” PVC pipe 2 – 4” PVC end caps, with appropriate holes 1 – heater (model#=Omegalux.
Soldering Safety – Soldering Irons are very HOT! Name: 1. When I am not using the soldering iron, I should return it to the holder because________ _________________________.
Plated Through Hole Soldering Materials by Lindsay Craig.
Computer Hardware Technology ELECTROBOT PROJECT. Computer Technology: ELECTROBOT Task: Teams of 2 will design and build an electronic control system for.
Colorado Space Grant Consortium Soldering 101. Caution: - Soldering is dangerous if not respected - Be mindful of where you are and where the soldering.
WIRE REPAIR Chapter 4. TROUBLESHOOTING STEPS l Confirm the Complaint l Study the electrical schematic l Locate and repair the fault l Test the repair.
1 Student Hands On Training I (2007) Timing Circuit & Camera Integration Timing Circuit & Camera Integration.
© 2017 SlidePlayer.com Inc. All rights reserved.