11 Types Available Edges Finish Material: Aluminum Panel Siding There are four main types of aluminum siding. Each one has slightly different characteristics and widths.Double 4″ Horizontal (D4)Provides a narrow width and wood grain finish. Very “traditional home” friendly.Double 5″ Horizontal (D5)Because it is slightly larger than it’s 4″ counterpart, this type of metal siding works great with larger homes. Wood grain. Single 8″ HorizontalClapboard with a wide profile. Lends itself to contemporary and traditional homes exquisitely. Offered in smooth and wood grain finishes.12 VerticalAKA “Board and Batten”. This siding offers a rustic appeal when used to cover the entire home. Offered in smooth and wood grain finishes.Types/Available Patterns & SizesLocationInstallationAccessories Necessary to Install MaterialDetailed Cost of Materials/AccessoriesManufacturers/Maintenance
12 Available Patterns/colors Finish Material: Aluminum Panel SidingSizes/ThicknessAvailable Patterns/colorsNominal thicknesses of aluminum siding range from .019” to .024”. The thicker the material, the more resistant to wind it will be and the more it will cost.Types/Available Patterns & SizesLocationInstallationAccessories Necessary to Install MaterialDetailed Cost of Materials/AccessoriesManufacturers/Maintenance
13 Available Patterns Location Finish Material: Aluminum Panel Siding Siding may be formed of horizontal or vertical boards may be attached directly to the building structure (studs in the case of wood construction), or to an intermediate layer of wood (boards, planks, plywood, oriented strand board)Types/Available Patterns & SizesLocationInstallationAccessories Necessary to Install MaterialDetailed Cost of Materials/AccessoriesManufacturers/Maintenance
14 Installation Finish Material: Aluminum Panel Siding Accessories Necessary to Install Material1.Angle Handle Hammer – $7.982.Foam board - $3.13-Gauge 2-in Stainless Steel Wood Siding Nails – $10.464.Durabuilt 4-in x 10-ft Vinyl Siding Outside Corner Post - $17.825.Homax Caulk Finisher – 2.746.Specialty Caulk – 11.977.Fractional Tape Measure – 4.988.4.5-in 20-Volt Cordless Cut-Off Tool Kit - $299.009.Door and Window Trim - $115.0810.Construction Adhesive - $12.98Obtain a permit for Aluminum Siding Installation from local building authority; post permit on the jobsite as required Prepare the area.Continue up the wall, interlocking the bottom of each sheet with the tops of the previous sheets.Use a circular saw to trim the siding panels that will be installed at windows, doors, and corners.Prepare the area.Install the underlayment.Add the corner posts.Install the top panels of siding by cutting any extra width from the top of the sheet.Install the footer.Place a strip of F-channel trim under the eaves.Apply caulk around any openings, such as doors and windows, to create an air tight seal.The typical Aluminum Siding Installation project involves tasks that are best performed by experienced professionals. Good quality Aluminum Siding Installation requires considerable experience, skill and attention to detail.Prepare the window and door trim.Install the trim so that it buts up against the tops and sides of the doors, and surrounds each window frame.Add your starter sheet of siding.Types/Available Patterns & SizesLocationInstallationAccessories Necessary to Install MaterialDetailed Cost of Materials/AccessoriesManufacturers/Maintenance
15 Detailed Cost of Materials/Accessories Finish Material: Aluminum Panel SidingManufacturersALSCO Building ProductsLimited Lifetime WarrantyTypes/Available Patterns & SizesLocationInstallationAccessories Necessary to Install MaterialDetailed Cost of Materials/AccessoriesManufacturers/MaintenanceMaintenanceAluminum is easily maintained in the first few years. After that the color may fade or paint may peel, blister or crack. Aluminum should be watched for dents, which should either be repainted or the panel replaced. Aluminum may need to be cleaned to remove dirt, grass, or mildew.
16 Questions??? Thank you for your attention!!! Presentation by: Aigerim JumatayevaQuestions???