Presentation is loading. Please wait.

Presentation is loading. Please wait.

Wilko Paint, Inc. Wilko Paint is the premier supplier of industrial finishes and coatings. Our staff of industrial coatings specialists will provide you.

Similar presentations


Presentation on theme: "Wilko Paint, Inc. Wilko Paint is the premier supplier of industrial finishes and coatings. Our staff of industrial coatings specialists will provide you."— Presentation transcript:

1 Wilko Paint, Inc. Wilko Paint is the premier supplier of industrial finishes and coatings. Our staff of industrial coatings specialists will provide you with the information necessary to meet or exceed your coating requirements. Founded in 1958, Wilko Paint has been developing products, providing technical support and training, and fulfilling industrial coatings needs for over fifty years. We are conveniently located in Wichita, Kansas and are part of a nationwide distribution system designed to serve you Ohio St., Wichita, Kansas

2 Wilkopon Coal Tar Epoxy A versatile rust inhibitive and protective coating for applying at temperatures as low as 35ºF!!!

3 TYPICAL USES Sewage treatment plants Power plants Refineries Pipes and Risers Undercoating Underground pipes and structures Suitable for use where water and chemical resistance are required

4 PROPERTIES Provides protection against fresh and salt water Provides protection against petroleum products, such as crude oil Capable of curing at temperatures as low as 35 F Can be applied at high film builds, mils DFT in one application Pipes may be buried within hours of application

5 Surface Preparation For maximum protection of steel surfaces, dry abrasive blast to a Commercial Blast Finish in accordance to SSPC-SP6-63 Concrete must be free of grease, wax, oil, or spalling, and if necessary, etched before painting If applied over marginally prepared areas, surface must be clean and dry, free from oil, grease, wax or any other contaminants

6 DRYING TIME Surface temperature must be at least 5ºF above dew point at all times to prevent moisture condensation, and to prevent entrapment of ice that will lead to holidays, and if sprayed applied, must be free of F.: To Recoat: 8 hours 6 hours 4 hours Dry Hard: 36 hours 12 hours 8 hours Full Cure: 14 days* 10 days 5 days *Complete cure will be attained upon exposure to higher temperature

7 Mixing Instructions Stir No A Wilkopon Coal Tar Part A until the material is uniform, then add 1 part Activator No B to four parts of Base No A and thoroughly stir the mixture for five minutes. Thinning is normally not required when applying with airless spray equipment. If needed or for conventional spray, thin with No. 71 Thinner only as necessary for atomization. Use of other thinner will affect pot life. Pot Life, w/336.12B: F F

8 APPLICATION EQUIPMENT Airless Spray: Standard airless spray equipment such as Graco Bulldog Hydra-Spray or larger, with inch fluid tip. Conventional Spray: Industrial equipment such as DeVilbiss MBC or JGA, or a Binks 18 or 62 spray gun and a material pressure pot with mechanical agitator. A moisture and oil trap in main air supply line is essential. Separate pressure regulators for air and fluid pressure are recommended. Brush or Roller Squeegee or Spatula

9 SPRAY APPLICATION PROCEDURE Apply a heavy wet coat in even, parallel passes with 50% overlap. Immediately follow with additional cross coat passes to obtain a continuous film with no pinholes, bare spots or holidays Apply additional material needed for the correct film thickness and repair of any pinholes or damaged areas within recoat time limit Do not overthin to avoid sags and for maximum film build

10 Application By Brush or Roller Application by brush or roller may require multiple application to achieve the desired film thickness

11 Application By Brush or Roller Application by brush or roller may require multiple application to achieve the desired film thickness Thin activated material until it is workable for roller or brush application.

12 Application By Brush or Roller Application by brush or roller may require multiple application to achieve the desired film thickness Thin activated material until it is workable for roller or brush application. Work the brush or roller into the surface in such a way that the surface contaminant is worked into the coating, and in the case of moisture, the brushing action will push the water aside to allow coating to come into contact with the substrate.

13 Application By Brush or Roller Application by brush or roller may require multiple application to achieve the desired film thickness Thin activated material until it is workable for roller or brush application. Work the brush or roller into the surface in such a way that the surface contaminant is worked into the coating, and in the case of moisture, the brushing action will push the water aside to allow coating to come into contact with the substrate. This method of application is recommended for maximum adhesion over marginally prepared surfaces or if light surface condensation is present.

14 RECOAT TIME Recoat within the following times to ensure proper intercoat adhesion: F 36 hours F 24 hours F 12 hours Surface Surface of the coating must be abraded by mechanical means if above recoat times are exceeded. Coal tar may bleed through if topcoated with other than itself.

15 Availability and Packaging is a stocked item and is readily available Available in one and five gallon kits Containers are conveniently short filled to allow addition of activator One gallon kit consists of Part A in one gallon container and Part B in a quart can Five gallon kit consists of Part A in a five gallon container and Part B in a gallon can

16 Contacts Corporate Office Tel or Fax Technical Information Don Holt – Ignacio Javier – Additional information (MSDS & TDS) may be obtained at Web Site:


Download ppt "Wilko Paint, Inc. Wilko Paint is the premier supplier of industrial finishes and coatings. Our staff of industrial coatings specialists will provide you."

Similar presentations


Ads by Google