Presentation is loading. Please wait.

Presentation is loading. Please wait.

Electronics-line.com. 2 Hardware Overview electronics-line.com 3 CommPact Main Module CommPact Modules SIM card holder Buzzer Contrast Trimmer Speaker.

Similar presentations


Presentation on theme: "Electronics-line.com. 2 Hardware Overview electronics-line.com 3 CommPact Main Module CommPact Modules SIM card holder Buzzer Contrast Trimmer Speaker."— Presentation transcript:

1 electronics-line.com

2 2 Hardware Overview

3 electronics-line.com 3 CommPact Main Module CommPact Modules SIM card holder Buzzer Contrast Trimmer Speaker Connector Siren Connector Siren Location Main CPU USB GSM/GPRS Engine (on back side of the board) Installed: 105dB Removed: 85dB

4 electronics-line.com 4 Power Connections Module PSTN, Zone33 & PGM connections CommPact Modules AC Supply and fuse Back Tamper Battery Connector Front Tamper Switch Transformer Installed: Open Collector Removed: Dry Contact

5 electronics-line.com 5 Features Overview

6 electronics-line.com 6 CommPact Product Overview 32 User codes 1 programmable speed dial numbers 6 programmable accounts Interfaces: GPRS, GSM and PSTN Remote firmware upgrade 32 wireless and 1 hardwire zones 1 onboard programmable output (PGM) 19 Keyfobs 4 Wireless keypads (2-way) Wireless siren (2-way) 4 Repeaters Arming Methods: Full, Part or Perimeter Event Log: 1022 event capacity Multilingual (14 languages)

7 electronics-line.com 7 Basic Operation Part ArmingFull ArmingPerimeter Arming Service Call - Record Vocal Message - Play Vocal Message - SOS Panic Alarm Activation - Chime Enable/Disable - Medical Emergency Alarm Activation - Fire Alarm Activation - Check Trouble condition

8 electronics-line.com 8 Wireless Devices Supervision Time Supervised wireless sensors send a supervision signal approximately one hour after their last transmission. If the system does not receive supervision signals from a specific transmitter, the transmitter is regarded as inactive. The amount of time after which a transmitter is considered inactive is called the Supervision Time. From the Programming menu, select Devices, Superv. Time, General [9,1,6,1]. Enter a supervision time between 02:00 and 23:59 hours.

9 electronics-line.com 9 Zone Configuration

10 electronics-line.com 10 Zone Configuration Zone Type ˗The zone type defines the type of alarm the system generates when the sensor is tripped. ˗To program a zone type: ˗From the Programming menu, select Devices, Zones [911]. ˗Select the sensor you want to program. ˗From the sensors sub-menu, select Zone Type [#02]. ˗Select one of the following zone types: Normal Entry/Exit Follower Panic Medical Fire 24Hr 24Hr-X (future option) Gas Flood Environmental No Motion Not Used

11 electronics-line.com 11 Zone Configuration Arm Set The Arm Set option allows you to define the arming methods in which the zone is included. To program the Arm Set option: From the Programming menu, select Devices, Zones [911]. Select the sensor you want to program. From the zones sub-menu, select Arm Set [#03]. Use the keys 1, 2 and 3 to toggle the current setting. Press when the desired setting is displayed.

12 electronics-line.com 12 Zone Configuration Bell Each zone can be programmed to activate the siren when triggered or to generate a silent alarm where only a message is sent to the central station. To program the Bell option: From the Programming menu, select Devices, Zones [911]. Select the zone you want to program. From the zones sub-menu, select Bell [#05]. Select either Enabled or Disabled.

13 electronics-line.com 13 Zone Configuration Chime When Chime is enabled, triggering the zone when the system is disarmed causes the internal siren to chime. To program the Chime option: From the Programming menu, select Devices, Sensors [911]. Select the zone you want to program. From the zones sub-menu, select Chime [#06].Select either Enabled or Disabled.

14 electronics-line.com 14 Zone Configuration Forced Arm Force arming enables you to arm the system when the system is not ready. If the magnetic contacts zone is defined as Force Arm disabled, the system will not be ready to arm until you close the door. To program the Force Arm option: From the Programming menu, select Devices, Zones [911]. Select the zone you want to program. From the zones sub-menu, select Force Arm [#07]. Select either Enabled or Disabled.

15 electronics-line.com 15 Zone Configuration Repeater The EL-2635 repeater is an additional module that extends the range of the wireless transmitters. For a sensor to use the repeater to relay transmissions to the system, you must define the Repeater option for its zone as Use Repeater. To program the Repeater option: From the Programming menu, select Devices, Zones [911]. Select the zone you want to program. From the zones sub-menu, select Repeater [#09]; the zones current Repeater setting is displayed. Select either No Repeater or Use Repeater.

16 electronics-line.com 16 Zone Configuration Entry/Exit delay The Entry/Exit delay timers determine the amount of time the user has to arm or disarm the system before an alarm is activated. You can program separate Entry and Exit delays for each arming method. To program Exit delay timers: From the Programming menu, select Entry/Exit, Entry/Exit Delays [921]. Select the Exit delay you want to program: Full [#1], Part [#2] or Perimeter [#3]. Enter a delay time ( seconds). Press when the desired setting is displayed.

17 electronics-line.com 17 User Code Types

18 electronics-line.com 18 CommPact Controlled/Non-controlled Codes When a controlled code used to Arm/Disarm the system the panel notifies the central station/end user. The panel will send a message to the control station only if the code was used after an alarm occurrence. Limited Codes This feature enables the user to issue a code that is valid for 24hrs only. This code automatically expires 24hrs after it was issued. Duress Code Designed for situations when the user is being forced to operate the system. When the code is being used the panel sends a Duress event message to the central station.

19 electronics-line.com 19 Telecontrol User Code Call Procedure ˗Call the CP either using the double call method (PSTN) or directly (Cellular); when the control panel picks up, two DTMF tones are sounded. ˗Enter the Telecontrol code (Code 29) on your telephone within 15 seconds. ˗The following DTMF commands are available: ˗Press 2 for Two-Way Audio. If the TWA mode is defined as Simplex the audio channel opens in Listen mode (microphone active/speaker mute). To switch to Speak mode, press 1 on your telephone. To switch back to Listen mode, press 0 on your telephone. ˗Press 3 to fully arm the system. ˗Press 6 to disarm the system. ˗Press 9 to cancel the siren. ˗Ten seconds before the timeout expires, two short DTMF tones are sounded. To extend the call, press 7 on your telephone. This command restarts the timeout. ˗To disconnect before the end of the timeout, press then # on your telephone. Tip: The Central Station cannot use the Telecontrol (for this purpose CMS can use the CS user code).

20 electronics-line.com 20 Voice Report Account Feature that calls the users telephone number when specific events occur and plays pre-recorded messages. Programming these accounts phone numbers is done in menu [9,5,1]. Tip: This requires enabling which is done in menu [9,4,13]. Additionally, in the event of an alarm, the user is able to establish a Two-Way Audio connection on receiving the vocal message in order to check the premises. Tip: This requires enabling which is also done in menu [9,5,1]. Home ID The Home ID is a short message that is played at the beginning of a voiced report call in order to identify the system to the user. To record the message access menu [9,5,19,2]. For example, Adams House shall be played before the event messages. To play the message access menu [9,5,19,1]. Message Center The Message Center is designed to allow the user to record a short message that may be played back later by another user. Play, Record and Delete menus [7,02,1]-[7,02,3]. Voice Report Options

21 electronics-line.com 21 Extra Features No Arm Indication The No Arm indication is a feature designed to inform the central station that the system has not been armed for a specified period of time. From the Programming menu, select System Options, No Arm Ind. [9,4,08]. Select 1 Week, 2 Weeks, 3 Weeks, 4 Weeks or Disabled. RF Jamming The system is able detect RF Jamming that is usually caused by an intruder attempting to compromise the security system. From the Programming menu, select System Options, Jamming Det. [9,4,09]. Select Enabled or Disabled. No Motion The No Motion feature is designed to monitor the activity of disabled or elderly people. If a sensor defined as No Motion has not detected within a pre-defined period of time, a No Motion event message is sent to the central station. During Disarm mode: No Motion ; During Arm mode: Normal From the Programming menu, select System Options, No Motion [9,4,10]. Select 01:00-72:00 Hours or Disabled.

22 electronics-line.com 22 Extra Features Arm On Exit The Arm on Exit feature cancels the unnecessary remainder of the Exit delay that continues to count down after the user has vacated the premises. This feature automatically arms the system when an Entry/Exit zone is closed during the Exit delay. From the Programming menu, select Entry/Exit, Arm On Exit [9,2,3]. Entry/Exit Trouble If this function is enabled, the system can't be armed when the Exit Delay expires, if one of the following conditions is present: An entry/exit zone is open; Tamper Alarm from a zone during exit (if not restored before the exit delay expires); Zone Active when Exit Delay expires. The event is then sent to the central station account. To program the Entry/exit Trouble option: From the Programming menu, select System Options, Entry Exit TR [9415]. Select Enabled or Disabled.

23 electronics-line.com 23 Two-Way Audio & Telecontrol Outgoing Calls ˗Service Call (Speed Dial)- this feature enables the user to establish a two-way audio connection with the central station operator. Tip: To program Service Call Phone Number access menu [9,5,3,1]. ˗CS TWA - In the event of Burglary, Fire and Medical alarms, the control panel is able to report the events and then stay on the line after ACK 2 is received. Tip: Two-Way Audio must be enabled for the specific account [9,5,1]. Incoming Calls ˗Telecontrol - Users may use this feature as a convenient way for contacting their family, operating their system or to check their home when they are away. Tip: For this feature to function, the Telecontrol User Code (#29) must be programmed. ˗Monitoring Station TWA User Code - User Monitoring service can contact the user in the event of an emergency or use this feature for listen-in alarm verification up to 10 minutes after the alarm. Tip: For this feature to function, the Central Station TWA User Code (#30) must be programmed. ˗For any of the incoming Telecontrol features to function, Telecontrol must be enabled in the Communication menu [9,5,4,10].

24 electronics-line.com 24 SMS Commands Remote Arming/Disarming via SMS Each SMS command contains the following elements: 1.SMS Command Descriptor (up to 43 characters of free text) 2.# (delimiter – separates the descriptor from the actual command) 3.User Code (4 digits) 4.Command (120=Disarm, 121=Full Arm, 122=Part Arm, 123=Perimeter Arm, 124=Full + Perimeter Arm, 125=Part + Perimeter Arm, 200 = Arm Status) The following example shows the format of an SMS command for arming the system. On receiving an Arm Status request message, the system returns a status message to the sender. Tip: The SMS Command feature must be enabled in order for it to function. Menu [9,5,4,13,4]. Tip: The SMS Confirm feature must be enabled in order for the CP to reply. Menu [9,5,4,13,5]. Partitions can be armed also remotely

25 electronics-line.com 25 System Initialization Options The Initialization function clears the entire system and resets factory defaults. Init All [9,7,1]. ˗For firmware versions that include multi-default and/or multi-language support, select the set of programming defaults and/or the required interface language that you want to load. Loading the systems default program enables you to restore the factory-set programming defaults. Load Defaults [9,7,2]. Clear User Codes deletes all programmed user codes and restores the default Master and Installer codes. Clear Users [9,7,3]. The Clear Wireless Transmitters function enables you to delete all registered transmitters at once. Clear Wireless [9,7,4].

26 electronics-line.com 26 Local Programming

27 electronics-line.com 27 Installation Procedure STEP 1: Opening the housing. STEP 2: Temporarily powering up the system. STEP 3: Registering the transmitters. STEP 4: Testing the chosen mounting location. STEP 5: Basic programming

28 electronics-line.com 28 Installation Procedure – Step1 Step1: Opening the Housing 1.Remove the housing screw located at the bottom of the front cover. 2.Using a screwdriver carefully press the release tabs as shown 3.Lift the front cover away from the back of the housing.

29 electronics-line.com 29 Installation Procedure – Step2 Step2: Temporarily powering up the system 1.In order to register and test transmitters, it is necessary to temporarily power up the system before installing the control panel. At this stage, do not connect the backup battery. 2. Thread the power cable through the wiring hole on the back cover and connect the cable to the AC power input on the Main board. 3.Note: At this stage, ignore any trouble conditions that may appear on the LCD display (e.g. Low Battery).

30 electronics-line.com 30 Installation Procedure – Step3 Step3: Registering transmitters 1.Press + installer code 2.Enter menu Programming devices [9,1] 3.Select the type of device (Zones, Keypads etc…) 4.Select the device number (Zone1, Zone2 etc…) 5.Trigger two transmissions from the device 6.The message Save? indicates the two transmissions have been successfully received. 7.Press to accept or to cancel the registration. 8.After accepting the registration, the display switches automatically to parameter settings for the current device (Zone Type, Descriptor etc…) – See next slide. 9.Tip: To check if a device number has already been registered, repeat steps 1 to 4. If a device has been registered previously, the system skips the registration function and switches automatically to parameter settings for the current device (Zone Type, Descriptor etc…)

31 electronics-line.com 31 Installation Procedure – Step3 Step3: Registering transmitters – Setting the zone parameters 1.Press to enter the zone type setting and use the arrow keys ( / ) to select the zone type. Normal (PIR), 24Hr (PIR/magnetic), Entry/Exit (Entrance magnetic), Gas (Gas sensor), Follower (Entrance PIR), Flood (Flood sensor) Panic (Panic button), Environmental (Universal TX), Medical (medical button), No Motion (PIR), Fire (Smoke sensor), Not Used. 2.Press to valid your choice, the display switches to Arm set setting. Set the arm set for this zone by pressing 1, 2 or 3. 3.Press to valid your choice, set the bell option for this zone 4.Press to valid your choice, set the chime option for this zone 5.Press to valid your choice, set the force arm option for this zone 6.Press to valid your choice, Press on several times to return to the main menu 1-Full2-Part 3-Perimeter

32 electronics-line.com 32 Installation Procedure – Step4 ZONE#1 S=9 OK Reduce the number of obstacle Consider the obstacle thickness Consider path angles Consider the wall material Step4: Testing the chosen mounting location 1.Press + installer code 2.Enter menu RF RSSI LEVEL (noise in the panel area) [7, 09, 2] = < 4 3.Enter menu TX TEST [7,07,2] > = 4 4.The system waits for transmissions. Activate the transmitter you wish to test; the transmitters signal strength is displayed and one to four tones are sounded accordingly. 5.If the signal strength is inferior to 4, move the transmitter to a better location as suggested below or use the EL-2635 repeater

33 electronics-line.com 33 Advances Tools for Simple Installation Installer built-in utilities List of all transmitters [7,07,1] ˗Smart Walk Test [7,06] ˗Transmitter Test [7,07,2] ˗RF RSSI Level (RF noise measured by the systems receiver) [7,09,2] RF RSSI =< 4 TX[7,07,2] – RSSI[7,09,2] > 2 // MUST! ˗GSM Strength Meter [7,09,1] > 4 ˗Wireless siren test [7,03] ˗Internal siren test [7,04] ˗Interface test [7,05] Real-time Transmitter list + status, signal strength meter ˗Visual (on LCD screen) ˗Audio (from speaker)

34 electronics-line.com 34 Installation tips EL-2601 Wireless magnetic switch ˗When connecting the device to the surface make sure that the metal screw does not stick out since it might create a short on the PCB. Plastic housingPCB Side view

35 electronics-line.com 35 Installation tips EL-2645 Wireless motion detector ˗Pulse Counter - The pulse counter determines the amount of beams that need to be crossed before the sensor will produce an alarm. The available options are 1, 2, 3 or Adaptive pulse count. Using the Adaptive pulse count feature, the detector chooses between 1 or 2 pulses based on its analysis of the received signal. We recommend setting the pulse count to Adaptive. ˗Pet Immunity The recommended mounting height when installing a pet immunity motion detector is 2.2 meters. Avoid locations where pets can climb.

36 electronics-line.com 36 Repeater – EL2635 Extends the range between control panel and wireless detectors. Ideal for problematic reception areas like attics, basements and cellars.

37 electronics-line.com 37 Enhancing the signal strength Repeater installation procedure ˗Register the sensor in the iConnect/CommPact system ˗Register the sensor in the repeater ˗Set the zone as Use repeater ˗Register the repeater in the panel ˗The repeater should be installed on the midway between the CP and the transmitter. Repeater CP

38 electronics-line.com 38 Repeater – EL2635 Up to 4 repeaters for one CP. 32 Transmitters registered to each repeater and 19 keyfobs,4 keypads, W/L siren. Registration & tests performed using a programming keypad.

39 electronics-line.com 39 Repeater Installation The repeater should be installed on the midway between the CP and the transmitter. Repeater CP

40 electronics-line.com 40 Repeater Installation Minimize the number of RF obstacles. The Repeater should be at least 1.50m above the floor and 1m below the ceiling. Apply all rules as for transmitters and receivers. 1.5m 1m

41 electronics-line.com 41 Repeater Installation Steps 1.Mount the CommPact control panel. 2.Register all the sensors to the CP. 3.Mount the sensors. 4.Identify the sensors having a low reception level. 5.Mount the repeater at halfway between the identified sensors and the control panel. 6.Register the repeater to the control panel. 7.Registering the identified sensors to the repeater.

42 electronics-line.com 42 Installation Procedure – Step5 Step5: Basic programming Set the communication parameters [951] Telephone number Account number Communication protocol (Contact ID,SIA, SMS Follow Me,SMS SIA,SMS Contact ID, TWA Follow me, Voice Report and IP Protocol) Communication interface (GPRS, GSM, PSTN) Call attempts Two way audio (Enable/disable) GPRS Network Parameters CP ID – Control panel identification; each control panel has a unique ID which is registered in the ELAS. [9573] CP Password – Control panel password; each control panel has a password which is authenticated when connecting to the ELAS. [9574]

43 electronics-line.com 43 Installation Procedure – Step5 GPRS Network Parameters CP ID – Control panel identification; each control panel has a unique ID which is registered in the ELAS. [9573] CP Password – Control panel password; each control panel has a password which is authenticated when connecting to the ELAS. [9574] GPRS Network APN – Name of the GPRS connection. Depend on the cellular service provider of the SIM card [95761]. Some APN need Username[95762] and password [95762]. IP Address of ELAS [9571] Port [9572]

44 electronics-line.com 44 2-Way Wireless Siren registration EL-2626AC Two-way Wireless Siren ˗On the control panel, define the siren type as 2-Way Siren.[9152] ˗Set the siren to Registration mode by placing the Mode jumper (JP1) as shown: ˗On the control panel, perform the External Siren Test twice in order to register the control panels transmitter to the EL- 2626ACs receiver.[702] ˗Set the control panel to Registration mode.[9151] ˗Set the siren to Transmission mode by placing the Mode jumper (JP1) as shown: REGISTRATION MODE TRANSMISSION MODE

45 electronics-line.com 45 Wired Siren Configuration (external wired siren (100mA Max. Load) ) 1.From the Control Panel, Press ''. Enter your Installer Code (the default Installer code is 1111). 2.From the Programming menu, select Output Trigger [9461]. Select Siren and press ''. 3.Select the Output Type (Steady) and press ''. 4.Select the Polarity (Active High) and press ''. 5.Define the PGM Cut-Off time (000 Sec.) 6.Press '' once more to save the configuration.

46 electronics-line.com 46 Remote Programming

47 electronics-line.com 47 Remote Programmer Electronics Line 3000s Remote Programmer (RP) software enables you to operate and program the system from a PC either on-site or from a remote location. You can connect to the control system from a PC using one of three methods: USB: A local connection using a USB to USB connector. GSM data number or PSTN: The RP calls the site via GSM using a Data number or PSTN. WebRP: The RP connects to the control system using the GPRS via the ELAS.

48 electronics-line.com 48 Remote Programming On-site and remote configuration Installer Fast Up/Downloading

49 electronics-line.com 49 Remote Mastering Monitoring station Real-time status check, command and event Log Fast Up/Downloading

50 electronics-line.com 50 Peripherals Overview

51 electronics-line.com 51 Intrusion Detection EL-2645/PI Wireless Motion Detector Microprocessor signal analysis for reduced false alarms, with optional 45kg/100lb pet immunity.

52 electronics-line.com 52 EL2601/2602 EL-2601 Wireless Magnetic Switch EL-2602 Universal Transmitter Detects intruder entry from doors and windows Intrusion Detection EL-2607 Wireless Vibration Detector Detects low amplitude vibrations around vulnerable access points for early detection of break-in attempts EL-2650XL Wireless Directional Curtain Detector Quad element directional solid curtain detector for perimeter protection. Narrow beam curtain allows free movement within protected premises.

53 electronics-line.com 53 Intrusion Detection & Event Notification EL-2635 Wireless Repeater Extends the range between the control panel and wireless detectors, eliminates problematic reception areas EL-2626AC Two-way Wireless Siren Supervised two-way wireless siren and strobe, A/C powered with battery back- up, available with red, amber or blue flash lens 85dB/106dB. EL-2606 Glass break detector Acoustic glass break detector with superior detection performance

54 electronics-line.com 54 EL-2621 Two-way Wireless Keypad Indicates current system status, controls 16 home automation devices and enables one-touch full/part/perimeter arm/disarm of system Additional Keypads and Keyfobs

55 electronics-line.com 55 Additional Keypads and Keyfobs EL 2711 Wireless Panic Button Wireless Panic Button Water resistant, wireless panic button with Pendant/Keychain option, for 24/7monitoring EL-2714 Wireless Multi-function Keyfob Keychain option, small, controls system functions like full/part/perimeter arm, disarm, home automation and panic

56 electronics-line.com 56 Environmental Safety EL-2661 Wireless Water Leak Detector Provides early warning of water leaks used in basement or near air conditioners and sinks EL-2703 Wireless Smoke Detector Photoelectric smoke detector, provides early warning of the presence of smoke. EN-54-7 approved

57 electronics-line.com 57 EL-2762 Wireless Gas Detector Detects leaks of household heating or cooking gas- methane, propane and butane. DC power EL-2764 Wireless CO Detector Detects and warns of carbon monoxide leaks Environmental Safety

58 electronics-line.com 58 Thank You Questions?


Download ppt "Electronics-line.com. 2 Hardware Overview electronics-line.com 3 CommPact Main Module CommPact Modules SIM card holder Buzzer Contrast Trimmer Speaker."

Similar presentations


Ads by Google