Presentation on theme: "Presented by: Mike Sisson February 23, 2012. It is the Law The Americans with Disabilities Act of 1990. It is the Right Thing to do Provide Equal Access."— Presentation transcript:
Presented by: Mike Sisson February 23, 2012
It is the Law The Americans with Disabilities Act of It is the Right Thing to do Provide Equal Access.
RC 67M Stable, Firm and Slip Resistant Surface. No Elevation Differences > ¼. Ramp Slopes 12:1 (8.33%) or Flatter. 2% Maximum Cross Slope. Detectable Warning Surface. Minimum 4 Wide Accessible Path (5 for New Const.).
Design/Bid/Build Department is Responsible for Design of Ramps. Contractor is Responsible for Construction. Design/Build Contract Item for Design of Ramps. Design/Build Team is Responsible for Design and Construction.
Read the Special Provisions. Review ramp locations early. Ensure ramp is within ROW, or obtain an Authorization to Enter. Ensure Technically Infeasible Forms (TIFs) are done before construction if ramp cannot fully meet the Standards.
Must use sound engineering judgment. Evaluated on a case-by-case basis. Must include reasons Standards cannot be met. Must include solution to provide access to the maximum extent feasible. Detail alternatives investigated. Submitted to ADA Coordinator in EXCEL format. Approved before construction.
Look for existing drainage issues. Know how to use the Smart Level: 2 vs. 4 level Calibrated Measure in percentage of slope (%), not degrees (°) Standard concrete placement requirements: Source of Supply Quality Control Plan Certifications Certified Concrete Technician
Verify appropriate design and TIFs approved. Check forms before, during, and after placement: Widths Depths Slopes (%, not °) Maximum and minimum slope rates are absolute (No construction tolerance). Standard concrete placement documentation. Install Detectable Warning Surfaces (DWS) per manufacturers recommendations. Complete Form CS 4401.
A Curb Ramp Inspection Form (CS-4401) is required for each curb ramp and will be used for the inspection of all altered curb ramps within the project limits to ensure compliance to PennDOT standards, contract documents, or provided access to the maximum extent feasible. The CS-4401 is a permanent record of how ADA ramps were built and should be retained in the project files. Inspector ultimately is responsible to ensure compliance.
This form contains field measurements, pictures of the constructed curb ramps, and images of the Technically Infeasible Form (if applicable). If any slopes or dimensions are out of range, the Inspector needs to compare the results to the design drawing(s). If the approved drawing(s) indicated all elements are ADA compliant, and the actual construction is not ADA compliant, the ramp must be reconstructed at no additional expense to the Department. The Inspector must verify the completed CS-4401 is accurate if the contractor or another person completes the form.
The electronic version of CS-4401 form can be found by going to the PennDOT homepage (www.dot.state.pa.us), selecting More Links… on the left side, then clicking Americans with Disabilities Act (ADA) and PennDOT. From there, you can then access all ADA related publications and forms.www.dot.state.pa.us When any part of the CS-4401 has a Red Cell, you must attach a TIF.
Note 8 To avoid chasing grade indefinitely when traversing the height of the curb, ramp length not to exceed 4500 (15-0). Adjust ramp slope as needed toprovide access to the maximum extent possible. Note 13Provide detectable warning surfaces (DWS) 610 (24) minimum (in the direction of pedestrian travel) across full width of ramp at the grade break near street edge. Provide DWS that contrast visually with adjacent walkway surfaces, either light-on-dark or dark-on-light for the full width of ramp. Note 15For new construction and alterations, construct curb ramp and flare slopes with the flattest slope possible. The slopes indicated in the details show the max slope allowable. Slopes that exceed those indicated in the details, or contract documents as applicable, will not be accepted and will be reconstructed.
Start coordinating early. Read the Special Provisions. If in doubt, ask questions. Consider drainage throughout the process Provide for a margin of error is possible.