We think you have liked this presentation. If you wish to download it, please recommend it to your friends in any social system. Share buttons are a little bit lower. Thank you!
Presentation is loading. Please wait.
Published byKallie Windley
Modified over 2 years ago
Hoop House Construction
Parts of the hoop house Frame Hoops Braces Plastic cover
Materials and Tools 2x4x8 (2) 2x4x4 (2) 1x2x8 (3) Nails (16d) Screws (1) 2 Corner braces (4) ½ Sch 40 PVC Pipe, 10 (4) ¾ Pipe straps (8) 10x20 Clear plastic sheeting Staples Wrench ¼ bolts. 2½ long (12) ¼ nuts (12) Washers (12) Tape measure ¼ drill bit Hammer Drill Utility knife Staple gun Duct tape, clear
The 2x4 Frame Build on flat, level ground. Line up 2x4s so they are square
2x4 Frame Corner braces and screws on inside corners Nails first on outside corners
Hoops Screw 4 pipe straps on inside of each long 2x4 One at each end and at 32 and 64 Loop the PVC pipes between opposite straps
Measure the distance between outside ends of the PVC hoops Cut the 1x2s to this length. It will be a few inches less than 8. Drill ¼ holes to line up with 4 hoops
Braces Drill holes in PVC to line up with braces A brace across the top A brace on each side 32 up Connect with bolts, nuts, and washers
Staple to frame and braces Cover staples with duct tape
Seal one end, maybe both
How to build a small inexpensive low-tunnel hoop house.
1. b. Rip Saw 2. d. Used for cutting with the grain.
Ledgewood Farm greenhouse construction How do I Start? to I’m Finished!
Hand tools. Standard Head Screw Driver Used to tighten or loosen flat head screws.
Plenum Seal From Above This photo shows a Cross-over connection, below a plenum from above. The arrows point to a large gap. Close up of large.
Building Boxes What is the largest volume open top box that you can build from an 8 ½ by 11 inch sheet of paper?
Tool Classification. Categories of Tools 1.Layout tools 2.Cutting tools 3.Boring tools 4.Driving tools 5.Holding tools 6.Turning tools 7.Fasteners.
… OF THE TRADE. TOOLS…. HAND TOOLS Tape Measure Usually metal, housed in a metal or plastic case Feature self-return spring to retract Range from 6-25.
General Instructions for “KidWind Light” wind tunnel.
Fasteners Any device used to hold 2 or more pieces of material together or in place Shank – long stem part of a nail/screw.
Tool Identification 1. Adjustable Wrench 2. Allen Wrench.
Tools and Fasteners And, Their Uses. A video quiz will follow this Power Point Presentation.
1/19/08Michael Long Eagle Project Plan 3/8” x 36” Metal Threaded Rods Approximately 16in. – Composed of 8 [2” x 4”x 8’] boards bolted together with 3/8”
How to build raised garden beds for small space gardening How to build a raised garden bed, which tools, material and skills needed. How much does it cost.
All About Flats By Samantha Lee. What is a flat? Theatre flats are large pieces of constructed and painted wood that are placed on the stage to serve.
Tool Identification A guide to the identification of Hand Woodworking Tools.
Tools English for Careers Class. tool belt A tool belt is used to hold tools on your body.
Kealakehe Chapter The non-circulating style. Hydroponics is the science of growing plants in water without soil. Kealakehe Chapter.
Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 7 Hand Tools, Fasteners, and Hardware.
Home Made Hovercraft Experiment By Abigail Despoy 10/5/11.
Hand Tool Identification Agriscience Technology Mr. Gibson.
Wood Chisel. Flat file Half round file Round file.
How to Build a Hovercraft October Patrick Wenzell How to Build a Hovercraft A Cobb County Technology-Based Integration School Special Thanks to.
Greenhouses limit increase: GCE Greenhouse Greenhouse: Building used to house and grow plants -Climate can be controlled -Amount of water.
Fasteners Nails Metal fasteners driven into the material it holds.
Theatrical Design and Production Chapter 8: Tools and Materials © 2006 McGraw-Hill. All right reserved. Hand Tools: Measuring Tools Tape Measure Plastic.
7x7=. 7x7=49 8x9= 8x9=72 4x7= 4x7=28 8x7= 8x7=56.
Tool Identification By:Gord Darling Construction Technology.
Using our imagination we can sometimes make a reasoned guess as to what may be concealed inside an object. We may even be lucky enough to have a magic.
How to Build a Divider Wall By Charysse Roberson.
Tool Identification Woodworking Hand Tools Manufacturing Tech 8 th Grade.
A/F Hexagon Construction Drawing Abilities Teacher © J Lewis 2004.
Potting Bench Plans Matt Howell Brooks County High School ___, Georgia Georgia Agricultural Education Curriculum Office, August, 2004.
Tool Identification. TURNING TOOLS Turn nuts, bolts, and screws.
Description of Hand Tools Tools help us do work and make things. Tools.
Objective Define tools and materials used in agricultural engineering careers.
Tool Identification Tool Identification and Use as Photographed and Prepared by Doug Best.
1 STEPMILL 7000 PT ASSEMBLY INSTRUCTIONS PART NUMBER
DRYWALL (LATHER) EVERYTHING ABOUT DRYWALL (LATHER)
Striking Nails! 9-1 Project 1. Purpose To find out which is the hardest wood out of 1. Oak 2. Maple 3. Poplar 4. Pine.
Potting Bench Plans Matt Howell Brooks County High School Quitman, Georgia Quitman, Georgia Georgia Agricultural Education Curriculum Office, August, 2004.
Sectional Assembly and Installation. Sectional Assembly & Installation Items Needed for Installation 1)6D Galvanized Screws 2)Silicone 3)1 ½ x 1 ½ x 3.
Bill of materials: Include the following Item name Number of pieces Type of material Size of pieces Total feet of different material Unit cost Total project.
Thinking about Safety!. Why is safety important? Equipment, Tools, materials, and activities determine how dangerous a situation is. You need to be.
Objective Identify types of fasteners. Types of Fasteners Nails are metal fasteners driven into the material it holds. –Common nails are used for.
Warlocks 8/5/05 TMU FIRST Robotics 101 u Week 1) Gears, Pulleys, Sprockets, Bearings u Week 2) Motors & Controls u Week 3) Pneumatics u Week 4) Materials.
Technical Theater Terms, Movement, Safety, Practices.
6.03 Tools in Agricultural Engineering Obj. 6.03: Remember tools and their safety practices related to the agricultural mechanics industry Images courtesy.
Section 2 Safety, Tools and Equipment, Shop Practices Unit 6: Fasteners.
© 2017 SlidePlayer.com Inc. All rights reserved.