1. 1 Introduction; Circuit Elements; Ohm's Law; KCL Prepared by: PANDYA SHIVANSHI(130320111037 ) CHHIKNIWALA PRANAVI(130320111007)

2. 2 Introduction Syllabus: textbook, homework, grading, schedule, reading assignments, laboratory Lectures: let’s avoid “Death by PowerPoint”

3. 3 Basic Electrical Quantities Basic quantities: current, voltage and power –Current: time rate of change of electric charge I = dq/dt 1 Amp = 1 Coulomb/sec –Voltage: electromotive force or potential, V 1 Volt = 1 Joule/Coulomb = 1 N·m/coulomb –Power:P = I V 1 Watt = 1 Volt·Amp = 1 Joule/sec

4. 4 Current, I Normally we talk about the movement of positive charges although we know that, in general, in metallic conductors current results from electron motion (conventionally positive flow) The sign of the current indicates the direction of flow Types of current: –direct current (dc): batteries and some special generators –alternating current (ac): household current which varies with time I(t)

5. 5 Voltage, V Voltage is the difference in energy level of a unit charge located at each of two points in a circuit, and therefore, represents the energy required to move the unit charge from one point to the other Circuit Element(s) +– V(t)

6. 6 Default Sign Convention Passive sign convention : current should enter the positive voltage terminal Consequence for P = I V –Positive (+) Power: element absorbs power –Negative (-) Power: element supplies power Circuit Element + – I

7. 7 Electrical Analogies (Physical)

8. 8 Active vs. Passive Elements Active elements can generate energy –Voltage and current sources –Batteries Passive elements cannot generate energy –Resistors –Capacitors and Inductors (but CAN store energy)

9. 9 Independent Sources An independent source (voltage or current) may be DC (constant) or time-varying (AC), but does not depend on other voltages or currents in the circuit +–+– Voltage Source Current Source

10. 10 Resistors A resistor is a circuit element that dissipates electrical energy (usually as heat) Real-world devices that are modeled by resistors: incandescent light bulbs, heating elements (stoves, heaters, etc.), long wires Resistance is measured in Ohms (Ω)

11. 11 Ohm’s Law v(t) = i(t) R- or -V = I R p(t) = i 2 (t) R = v 2 (t)/R[+ (absorbing)] v(t)v(t) The Rest of the Circuit R i(t)i(t) + –

12. 12 Open Circuit What if R =  ? i(t) = v(t)/R = 0 v(t)v(t) The Rest of the Circuit i(t)=0 + –

13. 13 Short Circuit What if R = 0 ? v(t) = R i(t) = 0 The Rest of the Circuit v(t)=0 i(t)i(t) + –

14. 14 Series Two elements are in series if the current that flows through one must also flow through the other. R1R1 R2R2 Series R1R1 R2R2 Not Series

15. 15 Parallel Two elements are in parallel if they are connected between (share) the same two (distinct) end nodes. ParallelNot Parallel R1R1 R2R2 R1R1 R2R2

16. 16 Kirchhoff’s Laws Kirchhoff’s Current Law (KCL) –sum of all currents entering a node is zero –sum of currents entering node is equal to sum of currents leaving node Kirchhoff’s Voltage Law (KVL) –sum of voltages around any loop in a circuit is zero

17. 17 KCL (Kirchhoff’s Current Law) The sum of currents entering the node is zero: Analogy: mass flow at pipe junction i1(t)i1(t) i2(t)i2(t)i4(t)i4(t) i5(t)i5(t) i3(t)i3(t)