2. 1 Copyright by PROFIBUS Center Nederland www.profibuscenter.nlinfo@profibuscenter.nl

3. 2 Some words to remember: ‘A good PROFIBUS developer is a PROFIBUS user’

4. 3 ‘ ’ ‘Learning how to define, develop and market a PROFIBUS DP or PA product according to the current guidelines.’ Purpose of this training course During this training course the roadmap from specifications up to the certification of the end product is laid out. We will start with the basics of PROFIBUS. This is done from the point of view of the end-users. When a PROFIBUS product developer does not know the requirements of the end-users, the product will result in commercial failure……

5. 4 RS 485 interface The attendee will learn how to make proper interfaces for RS 485 and MBP-IS.

6. 5 RS 485 electrical test Reflection test The reflection test exposes:  Long stub lines from connector to RS 485 driver.  Low impedance filters (parallel constructions). This test will only be performed when the device can communicate at baudrates higher than 1.5 Mbit/s! It is not allowed to have more than 500 mV reflection. The example on the left is bad! It is not allowed to have more than 500 mV reflection. The example on the left is bad! The attendee will learn about the certification process and how he can test his device himself.

7. 6 Certified FISCO equipment Highest Voltage & Current levels that can be fed to the device? Highest Voltage & Current levels that can be fed to the device? Residual L & C on field terminals (5 nF & 10 uH). Residual L & C on field terminals (5 nF & 10 uH). Circuit Isolation from Earth? Circuit Isolation from Earth? Case connected to Earth? Case connected to Earth? Energy storing elements in the device (C & L)? Energy storing elements in the device (C & L)? Certification/approval will detail:  The attendee will learn about FISCO design for PA equipment.

8. 7 What can be implemented in the diagnostic message? Operating time Module exchanged High or low limit exceeded Wire break Power supply too low Maintenance required Device is set to local control Device is in fail safe mode Device is not enabled Number of open/close cycles Temperature too high No sensor attached No compressed air Short circuit on output No power supply on I/O block I/O card error The attendee will learn how to make his product stronger.

9. 8 Subjects  Course material overview  Introduction to PROFIBUS technology  OSI model  Masters and slaves  Topology and transmission media  Token passing  Baudrates  DP-V0  GSD files  Basic DP demonstration  Exercise: Defining the I/O map of a DP slave  DP-V1  PA  Basic DP-V1/PA demonstrations

10. 9 Subjects (continued)  PROFIBUS FDL  Datalink services  Messages  SAPs  Busparameters  Basic FDL demonstrations  PROFIBUS DP-V0  Diagnostics  Parameters  Configuration  Global Control Command  Advanced DP demonstrations  Exercise: Defining configuration of a DP slave  PROFIBUS DP-V1  Class 1 & 2  API-Slot-Index  Parameters  Diagnostics  Advanced DP-V1 demonstrations

11. 10 Subjects (continued)  PROFIBUS PA  Profiles  Parameters blocks  Implementation requirements  Advanced PA demonstrations  Product specifications  Electrical and Mechanical  Software  Miscellaneous  Electrical interfaces  RS 485  MBP-IS  PROFIBUS hardware architecture  Interface between PROFIBUS and I/O  Core architecture  Single chip solutions (LSPM2)  SPC3  DPC31

12. 11 Subjects (continued)  SPC3 stack  GSD creation  Development tools  Certification procedure & hints  RS 485  MBP-IS  DP-V0  Questions and discussion

13. 12

14. 13 Course material overview Book 1  Presentations  Supplement sheets  Exercises and answers  Development checklists Book2  DP message decoding  SPC3 software example  GSD files  PA instrumentation  PA profile extract  PNO document: DP test specifications  PNO document: PA test specifications  PNO document: Interconnection technology  Test contract

15. 14 CD-ROM with useful information Contents:  Presentations, checklists and exercises.  Datasheets  PROFIBUS ASICs  Opto couplers  DC/DC converters  RS 485 drivers  Other components  PROFIBUS specifications and guidelines  Other specifications and guidelines  IS, FISCO, ATEX  GSD files  Software tools  GSD editor  Busmonitor  Demo version of ProfiScript  And more………

16. 15 PROFIBUS Product Development This training course is especially suited for product vendors and engineering companies who want to develop a PROFIBUS product. Step by step the routine from product specifications up to the prototype will be handled. PROFIBUS ASICs such as: SPC3, DPC31, SPC42, LSPM2 and SIM11 will be thoroughly explained. Subjects:  Technology overview of PROFIBUS DP, DP-V1 and PA  Product specifications  PROFIBUS ASICs  Development tools  Software drivers  Interface schematics (RS 485 and MBP)  Galvanic isolation and grounding  Connectors  GSD files  PROFIBUS PA profile V3  ATEX (explosion safety)  Product costs  Testing and certification