Presentation is loading. Please wait.

Presentation is loading. Please wait.

Machine Safety Review. Areas for safety review Identify this machine.

Similar presentations


Presentation on theme: "Machine Safety Review. Areas for safety review Identify this machine."— Presentation transcript:

1 Machine Safety Review

2 Areas for safety review

3 Identify this machine

4 Table Saw

5 Identify this machine

6 Router

7 Identify this machine

8 Scroll Saw

9 Identify this machine

10 Jointer

11 Identify this machine

12 Planer

13 Identify this machine

14 Band Saw

15 Identify this machine

16 Miter Saw

17 Identify this machine

18 Drill Press

19 Answer this question Cutting stock to width is called?

20 Ripping

21 Answer this question How high above the stock should the blade be on the table saw?

22 1/8” or “Half a Tooth”

23 Answer this question Using the fence involves what type of cutting?

24 Ripping

25 Answer this question How far should your fingers be from the table saw?

26 4”

27 Answer this question Using the miter gauge involves what type of cutting?

28 Crosscutting

29 Answer this question Can you use the fence and the miter gauge at the same time?

30 No - Kickback

31 Answer this question Identify one cause for a kickback?

32 Letting the wood drift away from the fence

33 Answer this question Identify another cause for a kickback?

34 Not using a push stick on narrow stock

35 Solution: kickbacks causes Not using a push stick on narrow stock Using the fence when you should be using the miter gauge Applying too much pressure to the left of the blade When the wood drifts away from the fence

36 Answer this question Typically, which machine would you use first after getting a board from the storage room?

37 Planer

38 Answer this question What is the shortest a board may be to use in the planer?

39 12”

40 Answer this question How much material may be safely removed in one pass on the planer?

41 1/16” – 1/3 of a turn on the handwheel

42 Answer this question Which direction should the grain go on the planer?

43 Straight in

44 Answer this question What two things must be “on” in order to use the planer?

45 Dust Collector, planer

46 Answer this question On which side does the planer cut?

47 Top

48 Answer this question Cutting stock to length is called?

49 Crosscutting

50 Answer this question What type of cutting does the power miter box saw do?

51 Crosscutting

52 Answer this question How far should your fingers be from the power miter box saw?

53 4”

54 Answer this question A board should be against what two things on the power miter box saw?

55 Fence, Table

56 Answer this question Identify a major safety concern when changing the bit?

57 Router turning on

58 Answer this question Where should the bit be when starting the router?

59 Off the wood

60 Answer this question What safety equipment must be worn at all times ?

61 Safety Glasses

62 Answer this question How high above the stock should the blade guard be set ?

63 ¼”

64 Answer this question Can the band saw blade be “backed out” of a curve? Explain why or why not ?

65 No, could pull blade off the wheels.

66 Answer this question Where should your fingers should be in relation to the band saw blade ?

67 On either side

68 Answer this question Should the band saw be used to cut small curves? Explain why or why not ?

69 No, will bend the blade.

70 Answer this question Where is the “danger zone” is on the band saw?

71 To the right:

72 Answer this question Where should the key chuck be when you start the drill press?

73 In the holder

74 Answer this question If your stock starts to spin while drilling, what should you do ?

75 Turn off the drill press, clamp down the stock.

76 Answer this question List two items to keep away from the revolving drill bit ?

77 Long hair, baggy clothes, jewelry, strings.

78 Answer this question Which direction should the teeth of the scroll saw blade be pointed ?

79 Down

80 Answer this question What does it mean if the blade of the scroll saw is bending? What should you do?

81 Too loose

82 Answer this question How do you cut an enclosed circle using the scroll saw ?

83 Loosen blade, put blade through hole, retighten blade.

84 Answer this question How much material can the jointer remove safely in one pass?

85 1/8”

86 Answer this question If you do not want to use a push stick, how wide does a board need to be?

87 Higher than the fence

88 — This is the last round —

89 Answer this question Should both edges of a board be jointed? Explain

90 No, they will be straight, but not parallel

91 Answer this question Should you joint the end grain of a board? Explain…

92 No, it will split the end

93 — End — Good luck on the test!


Download ppt "Machine Safety Review. Areas for safety review Identify this machine."

Similar presentations


Ads by Google