1. ROHIT INDUSTRIES GROUP (P) LTD Plant : 655-656, M.I.E Part-A, Bahadurgarh, Haryana HO : UG-10, Shivlok House No. 2, New Delhi - 15 Phone: +91-11-41427321, 41021800 Web: www.rigpl.com E: sales@rigpl.comwww.rigpl.comsales@rigpl.com

2.  1963 - Setup of RIGPL with mere 2 employees to start off with & small workshop  1992 - Setup of Modernised Delhi Plant  1996 - Setup of Bahadurgarh (Haryana) Plant  1998 - SOP for HSS Round Tool Bits  2002 - SOP for HSS Punches  2007 - Modernisation of Heat Treatment Plant  2008 - Setup of CNC Production Facility for Carbide End Mills  2011 - SOP for Solid Carbide Drills  2011 - SOP for Solid Carbide Reamers and Centre Drills  2012 – SOP for HSS End Mills & Centre Drills  2013 - SOP for HSS Bandsaw Blade Cutters  2014 – SOP for HAND CRAFTED – HIGH PERFORMANCE CARBIDE DRILLS

3.  Today RIGPL boasts of over 50,000 sq. ft of Area spread over 3- Manufacturing plants & 2 Sales Offices.  Over 80,000 items stocked in 2-warehouses  Over 100+ employees  Sales in excess of over USD 3.0 Million  Dedicated R&D Team for product improvements

4.  Type of HSS Tools ◦ Square & Flat / Rectangular in M2, M35, M42 & T42 ◦ Round Tool Bits in M2, M35, M42 & T42 grades ◦ Parting Blades in M2, M35, T42 ◦ Punches in M2 & ASP grade

5. ◦ 8-piece HSS Sets which includes TURNING TOOL (LH & RH), NOSE TURNING TOOL, ST. CORNER TURNING TOOL, PARTING OFF TOOL etc… ◦ HSS End Mills are available in M2, M35 grades  As per standard IS 6353 - 1991 & BS-122 (PART-1) 1953  Available in diameters 2mm to 50mm. ◦ HSS Centre Drills are available in M2, M35 grades  As per standards B.S. 328 (PART 2) 1950 or Type ‘B’ in IS : 6709 – 1977 or TYPE 'A' & 'R' as per IS : 6708/6710 – 1977  Available In Type “A” & Tpye “B”

6. Hack Saw Blade cuttersBand Saw Blade cutters

7.  End Mills & Ball Nose ◦ 1X Series  Suitable for non-ferrous, free cutting materials & materials below 30HRc hardness or materials with Tensile strength <800N/mm 2 ◦ TX Series  Suitable for machining SS, Steels in hardness range from 30 to 50HRc ◦ 3X series  Suitable for machining Hardened dies in range of 50-60HRc like P20, D2, D3, H13 etc.  Machining Titanium & Harder to machine SS alloys.

8.  Super-Cut Series (HIGH FEED CUTTERS – pg.91)  Replace your Ball Nose in roughing or semi finishing operations with SUPER-CUT End Mills  Suitable for HSFM (High Speed Feed Machining)  Reduces machining time considerably; you do NOT have to think of your productivity again  Suitable for machining hardened dies above 60HRc like D2, D3, H13 and other types of Tool & Die steels

9. Taper End MillDouble Sided End MillBull Cutter End Mills with Taper Neck

10.  Standard Drills  Stub Series (as per DIN 6539)  Suitable for General Purpose Drilling  For drilling depths up to 3L/D to 5L/D ratio  Jobber Series (as per DIN 338)  Suitable for General Purpose Drilling  For drilling depths up to 3L/D to 5L/D ratio  Newer High Performance & Steel Machining Series ◦ Less than 10microns Run-out in the tools ◦ Best suited for High Productivity & stiff tolerance runs ◦ 25-30% increase in Feed & Speed rates than standard drills

11.  Through Coolant or Coolant Fed Series  70% Higher Speed & Feed rates than standard drills  30 degree helix for better chip evacuation  Minimum 500psi of coolant pressure recommended for usage  For drilling depths up to 3L/D to 15L/D ratio  Special 4-Facet design for High Performance  Available in 2 & 3Flute

12. Step / Combination Drills Countersink / Chamfer Drills Through Coolant Drills Spade Drills

13.  Carbide Reamers ◦ Straight Flute Reamer  Suitable for blind hole application  Suitable for moderately hard materials ◦ LHS / RHC Reamer  Suitable for Hard materials like Steel, SS etc..  Better finish  Better tolerance & feed control  Used only in Through hole application ◦ RHS / RHC Reamer  Suitable for Aluminum & free cutting materials  Blind Hole applications

14. THANK YOU !