1. San Jose, California USA
Geometrics, Inc.
45 years experience in making geophysical instruments
San Jose, California USA
Douglas Groom, Director of Geoelectrical Products

2. Geode EM3D New geophysical instrument for High-resolution CSAMT surveys (controlled source audio magnetotellurics) Minex Central Asia, April 2014 Astana, Kazakhstan

3. Geode EM3D Features What is it?
Distributed network of up to forty EM receivers each have six channels for total 240 EM channels
Each receiver configurable for up to six telluric (E-field) channels and up to three magnetic (H-field) channels
Durable metal enclosure.
Low noise front end as low as 10 nV/rtHz
Low distortion front end
Automatic calibration in the field
Automatic contact resistance measurement in the field
Much more

4. Highlights
Synchronized electric and magnetic field measurements for CSAMT, AMT, and more
Synchronized by GPS to CSAMT transmitter
Rugged instrumentation
Reliable network architecture
Backed by 45 years of experience in geophysical instrument manufacture

5. Geode EM3D 24-Channel Network 20 E – 4 H Channels

6. Benefits Why use it?
High-density 3-D data sets for complete characterization of your mining prospect
Rapid data collection with all channels GPS-synchronized to a single transmitter
Flexible spacing of H-field sensors to maximize resolution yet minimize cost
Scalable network from 6 channels up to 240 channels
Full tensor CSAMT using two transmitter polarizations
Automatic contact resistance measurement for better data quality
In-field calibration for more accurate measurement
Future AMT, IP, Resistivity modules available

7. Geode EM3D Single Receiver

8. High-resolution, high-density EM data with many sounding stations at the same time (simultaneous data acquisition).
Traditional CSAMT uses a separate setup for each sounding.
For example, for 50 traditional CSAMT stations (soundings) the transmitter must be run fifty times and the station moved 50 times. Typically 30 minutes to one hour transmitter run time for each station meaning 50 hours of transmitter time for the survey, not including setup time.
Geode EM3D allows a single setup of all stations and one transmitter run for acquisition of all 50 sounding at the same time (simultaneous acquisition). That is only 30 to 60 minutes in total for all 50 stations.

9. Orienting and leveling magnetic coils can be the most time consuming process in setting up a station

10. Geode EM3D offers flexibility in the use of H-field magnetic sensor coils
Saves time: Traditional CSAMT requires burying coils for every sounding. Each time the station is moved the coils are reburied. Geode EM3D network allows using magnetic coils on one receiver to be used for multiple soundings on other receivers so fewer coils need to be buried.
Improves efficiency: Operator can choose the optimal number of magnetic coils for the survey needs. For example H-field measurements can be used for every two E-field measurements, or maybe only every six, ten, or more E-field measurements, depending on the complexity of the geology and the requirements of the survey.
Improves data quality: Using multiple Hy and Hx on different receivers, at different locations simultaneously, allows local referencing to improve data quality.

11. Flexible networking

12. Easily scalable system from single-receiver 6-channel system to 40-receiver, 240-channel system
Maximum flexibility in survey setup. Each receiver can be any combination of E and H up to six channels, such as:
3E/3H
4E/2H
5E/1H 6E

13. Field setup and channel parameters Note automatic contact resistance for every E-field dipole

14. GeodEM2010 Acquisition Menu Note “Measure Contact Resistance” and “Measure AC & DC Level”
Contact resistance measured on automatically on all electrode channels. AC and DC noise level measured automatically.

15. China GeoTech Beijing
Introduction of multi-node Geode EM3D to Chinese

16. 120-Channel, 20-Receiver setup on bench

17. Exhibit interest

18. In-field screen display of test signal into 120 channel Geode EM3D

19. Better results with full tensor CSAMT
Traditional CSAMT only does scalar (Ex/HY) impedance calculations. The Geode EM3D can easily do full-tensor measurements (Ex/Hy and Ey/Hx) using multiple polarizations from the controlled-source transmitter.

20. Geode EM3D field test approximately 100 km north of Beijing
Four receiver network consisting of 20 channels used.
Four magnetic (H-field) channels
Sixteen electric (E-field) channels
Four channels not deployed

21. Phoenix T-3 3 kW transmitter

22. Transmitter + Controller + Generator + PDA Monitor

23. Planting the transmitter dipole

24. Grounding transmitter dipole with metal plates and stakes

25. Chinese made 30 kW transmitter + controller + power supplies + junction boxes + monitoring gear

26. Two 15 kW generators for 30 kW Chinese transmitter

27. Set up frequency scheduler

28. CSAMT field data 16 channels at 8 Hz with 1. 5 kW transmitter at 12
CSAMT field data 16 channels at 8 Hz with 1.5 kW transmitter at 12.5 km distance

29. CSAMT field data 16 channels at 8 Hz with transmitter at 12
CSAMT field data 16 channels at 8 Hz with transmitter at 12.5 km distance

30. Real-time CSAMT impedance curves for six soundings in field

31. CSAMT and AMT now with future, IP, resistivity and other methods in future
The first Geode EM3D product is controlled source audio magnetotellurics (CSAMT). Future products plans include AMT (natural-field audio magnetotellurics), induced polarization (IP) resistivity and other geoelectrical techniques.

32. Setting parameters for AMT acquisition Note that seven channels defines tensor site
Ex, Ey, Hx, Hy, Hz, Hx2 and Hy2 for local reference

33. AMT real-time times series field display (natural field with no transmitter)

34. AMT

35. AMT

36. Real-time field data processing

37. GEM3D receiver with coil cables, porous pot, dipole cables, battery, Ethernet cable

38. Retrieving 250-m Ethernet cables at end of day

39. System Configurations
1. Single Node
One GeodeEM box used for AMT/CSAMT/IP with various configurations 6E, 5E1H, 4E2H, 3E3H
2. “Typical” Small Networked System
Four Geode EM3D receivers is the base network, with various configurations possible
3. “Maximum” Networked System
40 GeodeEM boxes, i.e. 240 channels.
20 Geode EM networ of 110 on display in Laurel Geophysical booth in exhibition hall.